Cisco E2500 Manual de usuario

Revision 1.0 Page 1 ®® Linksys® E2500 Wireless-N Router Configuration Guide Revision 1.0 Copyright © 2012 Maretron, LLP A

Linksys® E2500 Wireless-N Router Configuration Guide From the Basic Setup page, open the DHCP Reservation Table by pressing the DHCP Reservatio

®® Press Add Clients to add the IPG100 to the table: Press Save Settings and then Close. To make these settings take effect, reset the IPG10

Linksys® E2500 Wireless-N Router Configuration Guide 2.3 Adding a PC based N2KServer® to the Network. In addition to the PC connected to the W

®® The DHCP Reservation table is displayed as shown below: Carefully copy the Client Name and MAC Address for the PC from the top table to th

Linksys® E2500 Wireless-N Router Configuration Guide Press Add Client to add the PC to the table. Press Save Settings and then Close. To make

Revision 1.0 Page 15 ®®If the default values are used this should be 192.168.1.3. A message should be displayed at the bottom left of

Linksys® E2500 Wireless-N Router Configuration Guide Page 16 Revision 1.0 Press the Connect button to establish the connection. 2.7 Adding

®® 3 Resetting the WiFi/Router to Maretron Configuration In addition to the parameters that must be set by the user described in paragraph 2,

Linksys® E2500 Wireless-N Router Configuration Guide You will now see another warning screen. Click the checkbox next to “I understand that my

®® You will now see the router’s manual configuration screen, and can proceed to the next steps. 3.3 Give your Wireless Network a name When

Linksys® E2500 Wireless-N Router Configuration Guide Page 2 Revision 1.0 Revision History Rev. Description 1.0 Original document

Linksys® E2500 Wireless-N Router Configuration Guide There are two Network Name (SSID) fields, in both of them, replace the word Cisco with Ma

®® The Passphrase is used to encrypt the data passed between the router and wireless devices. It must be entered identically on all wireless

Linksys® E2500 Wireless-N Router Configuration Guide Page 22 Revision 1.0 Appendix A- Client/Server Architecture The N2KView® Vessel Monit

®® A.1 Examples of NMEA 2000® Client/Server Architectures N2KServer® may run on a Windows PC (using Maretron’s USB100 gateway - see Section 2

Linksys® E2500 Wireless-N Router Configuration Guide Figure 3 extends the example shown in Figure 2by adding an external internet access point

Revision 1.0 Page 25 ®®typically found as part of a router. The router can be configured to reserve a specific address for the compute

Linksys® E2500 Wireless-N Router Configuration Guide Page 26 Revision 1.0 N2KView® must then be set up to request a connection to the WAN I

Revision 1.0 Page 27 ®®The N2KView® system protects your vessel’s data with multiple levels of protection. First, any data that pass

Revision 1.0 Page 3 ®®Table of Contents 1 Introduction ...

Linksys® E2500 Wireless-N Router Configuration Guide 1 Introduction Thank you for purchasing the Maretron preconfigured Linksys® E2500 Wireles

Revision 1.0 Page 5 ®®and control software (client) and Maretron’s N2KServer® (server). If you are installing a system similar to Figu

Linksys® E2500 Wireless-N Router Configuration Guide 2 Configuring the WiFi/Router The settings in the WiFi/Router are changed using a web bro

®® From now on, we will just show one set of browser screens – the screens from other browsers will be very similar. Leave the User name blan

Linksys® E2500 Wireless-N Router Configuration Guide You are now connected to the WiFi/Router, and should see the following basic setup screen.

®® Whenever you make a change to the configuration, you will see the following message: You can press Continue whenever this message is displ