Cisco XM Universal Gateways Cisco AS5400XM Manual de usuario Pagina 48
- Pagina / 100
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4-2
Cisco AS5400XM Universal Gateway Chassis Installation Guide
OL-6418-02
Chapter 4 Troubleshooting
Mixing WAN DFCs
Mixing WAN DFCs
The Cisco AS5400XM supports only one type of WAN DFC at a time. The DFCs that can be installed
at one time are:
• Four T1 DFCs
• Four E1 DFCs
• One CT3 DFC and three T1 DFCs
The Cisco AS5400XM software recognizes DFCs in the order of the slots they are in. For example, a
DFC in slot 2 is recognized before a DFC in slot 3. The system recognizes if there is a mix of WAN DFCs
during both power up and OIR:
• During power up, the first WAN DFC recognized by the system is the only type brought up.
• If there are two or more WAN DFCs of the same type and one is hot-swapped with another of a
different type, the new one is not recognized.
In both situations, an error message appears on the console that is similar to the following example:
00:01:12:%CARRIER-2-T1_E1_MIX:Cannot mix T1 and E1 8PRI DFC cards in chassis, do not power
up invalid card in slot 7
Ta b l e 4-1 Chassis LEDs
LED State Description
Alarm On An alarm error has been detected.
Off Remains off when operation is normal.
Gigabit Ethernet Activity (ACT) Flickering The Gigabit Ethernet LAN connection is transmitting and receiving data
normally.
Gigabit Ethernet Link (LNK) On The Gigabit Ethernet cable is connected properly.
Off The Ethernet LAN connection is not transmitting or receiving data.
Check the Ethernet cable connections.
OK/MAINT On The system board is operating normally.
Off Power is off or the system has not booted.
Blinking A memory failure occurred.
Serial Ports Activity (ACT) Flickering The serial port connection is transmitting and receiving data normally.
Serial Ports Link (LNK) On The serial port cable is connected properly.
Off The serial port cable is not connected properly.
BITS Port On Indicates a valid signal on the BITS port.
Off Remains off when operation is normal.
Remote Alarm (RA) On Indicates a T1 alarm condition encountered by software.
Off Remains off when operation is normal.
Local Alarm (LA) On Indicates a T1 alarm condition encountered by software for a particular
port.
Off Remains off when operation is normal.
- Chassis Installation Guide 1
- CONTENTS 3
- 4 Troubleshooting 4-1 4
- Contents 5
- Document Organization 7
- Waarschuwing 9
- Varoitus 9
- Attention 9
- Avvertenza 10
- Advarsel 10
- ¡Advertencia! 10
- Varning! 10
- Document Conventions 11
- Obtaining Documentation 14
- Documentation Feedback 15
- • 1 877 228-7302 16
- • 1 408 525-6532 16
- Submitting a Service Request 17
- Overview 19
- Chapter 1 Overview 20
- Dial Feature Cards 21
- Power Supply 21
- Specifications 22
- Preparing to Install 23
- Safety Recommendations 24
- Required Tools and Equipment 25
- Network Specifications 26
- Ethernet Connections 27
- Console and Auxiliary Ports 27
- 2T Serial Ports 28
- Alarm Port 28
- BITS Port 28
- Power Supply Considerations 28
- Statement 13 29
- Setting Up the Chassis 31
- Universal gateway 32
- Rack-Mounting the Chassis 33
- Installing in a Rack 34
- Connecting to the Network 35
- Connecting to a WAN 36
- T1/E1 8 PRI 37
- RJ-45 jack 37
- Straight-through 37
- RJ-45-to-RJ-45 cable 37
- E1 cable 38
- Console port 39
- Connecting to the BITS Port 40
- Connecting to the Alarm Port 41
- Supplying Power 42
- Connecting the AC Power Cord 43
- Wiring the DC Power Supply 43
- Where to Go Next 45
- Troubleshooting 47
- Mixing WAN DFCs 48
- Environment Monitoring 49
- Displaying Environment Status 50
- Getting Help 53
- Replacing Memory Components 55
- Chassis Cover Removal 56
- Removing the Chassis Cover 57
- Chassis bottom 58
- Front panel 58
- Chassis cover 58
- Replacing the Compact Flash 59
- Figure A-4 Memory Locations 60
- Replacing DIMMs 61
- Statement 1041 62
- Replacing the Chassis Cover 63
- Chassis Cover Replacement 64
- Replacing the Power Supply 67
- Statement 140 69
- Removing the Power Supply 71
- Mounting 72
- Power supply 72
- Air separator 72
- Figure B-7 Removing the Fan 73
- Installing the Power Supply 76
- Figure B-13.) 78
- Sheet metal tabs 80
- Bridge lance 80
- Base tabs 80
- Fan connector 81
- Cabling Specifications 89
- Ethernet Port Pinouts 92
- BITS Cable and Port Pinouts 93
- Alarm Port Pinouts 93
- Bantam Jack Port Pinouts 94
- Numerics 95
- OL-6418-02 100
Relacionado con productos y manuales para Hardware Cisco XM Universal Gateways Cisco AS5400XM
Hardware Cisco OL-15491-01 Manual de usuario
(268 paginas)
(268 paginas)
Hardware Cisco 1711 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Cisco XR 12406 Manual de usuario
(252 paginas)
(252 paginas)
Hardware Cisco WUSB600N Manual de usuario
(43 paginas)
(43 paginas)
Hardware Cisco 12000 Series Manual de usuario
(10 paginas)
(10 paginas)
Hardware Cisco 7200 Manual de usuario
(50 paginas)
(50 paginas)
Hardware Cisco WUSB54GC Manual de usuario
(33 paginas)
(33 paginas)
Hardware Cisco 3825 Series Manual de usuario
(20 paginas)
(20 paginas)
Hardware Cisco 2000 Manual de usuario
(6 paginas)
(6 paginas)
Hardware Cisco 7301 Manual de usuario
(34 paginas)
(34 paginas)
Hardware Cisco WRV54G Manual de usuario
(101 paginas)
(101 paginas)
Hardware Cisco 700 MHz Manual de usuario
(134 paginas)
(134 paginas)
Hardware Cisco 3600 Series Manual de usuario
(18 paginas)
(18 paginas)
Hardware Cisco 1721 Manual de usuario
(92 paginas)
(92 paginas)
Hardware Cisco 1701 Manual de usuario
(10 paginas)
(10 paginas)
Hardware Cisco 1710 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Cisco 1751 Manual de usuario
(98 paginas)
(98 paginas)
Hardware Cisco EPC3212 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Cisco 2500 Series Manual de usuario
(6 paginas)
(6 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales