Cisco 3750-48TS - Catalyst Switch - Stackable Especificaciones

GETTING STARTED GUIDE Catalyst 3750 Switch Getting Started Guide1 About this Guide2 Taking Out What You Need3 Running Express Setup4 Managing the Swi

10 5 Planning Switch StacksBefore connecting the Catalyst 3750 switches in a stack, keep in mind these planning considerations:• The size of the swit

11 Cabling ConsiderationsThese illustrations show the recommended Catalyst 3750 switch stack configurations with redundant StackWise cabling connectio

12 Side-By-Side StackingIn this example, eight switches are stacked side-by-side with redundant connections by using 0.5- and 3-meter StackWise cables

13 6 Rack-MountingThis section covers basic 19-inch rack-mounting and switch port connections. As an example, all the illustrations show the Catalyst

14 Installation Warning StatementsThis section includes the basic installation warning statements. Translations of these warning statements appear in

15 WarningIf a redundant power system (RPS) is not connected to the switch, install an RPS connector cover on the back of the switch. Statement 265War

16 Attaching the BracketsUse four Phillips flat-head screws to attach the long side of the brackets to Catalyst 3750 switches in one of three mounting

17 Rack-Mount the SwitchUse the black Phillips machine screw to attach the cable guide to the left or right bracket. Use the four number-12 Phillips m

18 Connect the StackWise CablesFollow these steps to connect the StackWise cable to the StackWise ports:Caution Removing and installing the StackWise

19 Connect to the Switch PortsThis section describes how to connect to the fixed switch ports, the SFP module ports, and the XENPAK module ports.Conne

2 1 About this GuideThis guide provides instructions on how to use Express Setup to initially configure your Catalyst switch. Also covered are switch

20 Install the SFP Modules and Connect to the PortsFollow these steps:For a list of supported modules, see the release notes on Cisco.com. For detaile

21 Install the XENPAK Module and Connect to the PortsFollow these steps to install a XENPAK module into the XENPAK module slot on the front panel of t

22 7 In Case of DifficultyIf you experience difficulty, help is available in this section and also on Cisco.com. This section includes Express Setup

23 Resetting the SwitchThis section describes how to reset the switch by rerunning Express Setup. These are reasons why you might want to reset the sw

24 For More InformationFor more information about the switch, see these documents on Cisco.com:• Catalyst 3750 Switch Hardware Installation Guide• Reg

25 CCDE, CCENT, CCSI, Cisco Eos, Cisco Explorer, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Nurse Connect, Cisco Pulse, Cisco SensorB

Americas HeadquartersCisco Systems, Inc.San Jose, CA Asia Pacific HeadquartersCisco Systems (USA) Pte. Ltd.SingaporeEurope HeadquartersCisco Systems I

3 Shipping Box ContentsCatalyst 3750 switchConsole cable(optional)Two 19-inchmounting bracketsFour number-12 Phillips machine screwsFour number-8 Phil

4 3 Running Express SetupWhen you first set up the switch, you should use Express Setup to enter the initial IP information. This enables the switch

5 Step 7Connect a Category 5 Ethernet cable to any 10/100 or 10/100/1000 Ethernet port on the switch front panel.Connect the other end of the cable to

6 Step 11Enter this information in the Network Settings fields:• In the Management Interface (VLAN ID) field, the default is 1. Enter a new VLAN ID on

7 Step 14(Optional) Enter this information in the Advanced Setting fields:• In the Telnet Access field, click Enable if you are going to use Telnet to

8 Refreshing the PC IP AddressAfter you complete Express Setup, you should refresh the PC IP address:• For a dynamically assigned IP address, disconne

9 3. Download the Network Assistant installer, and run it. (You can run it directly from the Web if your browser offers this choice.)4. When you run t