Cisco 2513 Especificaciones Pagina 18
- Pagina / 138
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2-4 Router Installation and Configuration Guide
General Site Requirements
Caution For safety, periodically check the resistance value of the antistatic strap, which
should be between 1 to 10 megohms (Mohms).
General Site Requirements
This section describes the requirements your site must meet for safe installation and
operation of your system. Ensure that your site is properly prepared before beginning
installation.
Site Environment
The router can be placed on a desktop or mounted in a rack or on a wall. The location of
the chassis and the layout of your equipment rack or wiring room are extremely important
for proper system operation. Equipment placed too close together, inadequate ventilation,
and inaccessible panels can cause system malfunctions and shutdowns, and can make
system maintenance difficult.
When planning your site layout and equipment locations, remember the precautions
described in the next section, “Preventive Site Configuration” to help avoid equipment
failures and reduce the possibility of environmentally caused shutdowns. If you are
experiencing shutdowns or unusually high errors with your existing equipment, these
precautions may help you isolate the cause of failures and prevent future problems.
Preventive Site Configuration
The following precautions will help you plan an acceptable operating environment for your
router and will help you avoid environmentally caused equipment failures.
• Electrical equipment generates heat. Ambient air temperature might not be adequate to
cool equipment to acceptable operating temperatures without adequate circulation.
Ensure that the room in which you operate your system has adequate air circulation.
• Always follow the ESD-prevention procedures described in the section “Preventing
Electrostatic Discharge Damage” earlier in this chapter to avoid damage to equipment.
Damage from static discharge can cause immediate or intermittent equipment failure.
- About This Guide 1
- Organization 2
- Conventions 2
- Overview of the Router 5
- Hardware Features 6
- Overview of the Router 1-3 7
- Overview of the Router 1-5 9
- System Specifications 10
- Obtaining Service and Support 11
- Cisco Connection Online 12
- Ordering Documentation 13
- ISDN Connections 21
- DTE or DCE 22
- Signaling Standards 24
- Router connections 25
- EIA/TIA-449 V.35 X.21 25
- EIA/TIA-232 EIA-530 25
- EIA/TIA-232 Connections 26
- EIA/TIA-449 Connections 26
- V.35 Connections 27
- X.21 Connections 28
- Where to Go Next 31
- Installing the Router 33
- Required Tools and Equipment 34
- Setting Up the Chassis 35
- Rack-Mounting the Chassis 37
- Wall-Mounting the Chassis 39
- TOKEN RING 41
- DC Power Specifications 42
- Wiring the DC Power Supply 43
- Input: –40– –72V 44
- Current: 1.5–1.0A 44
- Watts: 40W 44
- Connecting to a Network 45
- Installing the Router 3-17 49
- AUX SER 0 ETH 51
- Installing the Router 3-21 53
- Configuring the Router 55
- Configuring the Router 4-3 57
- Configuring the Router 4-5 59
- Configuring the Router 4-9 63
- Configuring the Router 4-11 65
- Using Configuration Mode 66
- Using AutoInstall 67
- Cisco IOS Software Basics 68
- Saving Configuration Changes 71
- Configuring ISDN 72
- SPID_no [LDN] 74
- Example ISDN Configuration 75
- Configuring ISDN 76
- Getting More Information 77
- Troubleshooting the Router 79
- Isolating Problems 80
- ° F (0to40°C) 80
- Reading the LEDs 81
- Figure A-3 Model 2503 LEDs 82
- Figure A-4 Model 2504 LEDs 82
- Figure A-5 Model 2513 LEDs 82
- Figure A-6 Model 2514 LEDs 83
- Figure A-7 Model 2515 LEDs 83
- Maintaining the Router 85
- Opening the Chassis 86
- Screw Slot 87
- Flat-blade screwdriver 87
- Maintaining the Router B-5 89
- Maintaining the Router B-7 91
- Upgrading the DRAM SIMM 92
- • ESD-preventive wrist strap 94
- • System-code SIMM(s) 94
- System-Code SIMM Replacement 95
- Closing the Chassis 97
- Cable Specifications 99
- Identifying a Roll-Over Cable 100
- Token Ring Port Pinouts 105
- EIA/TIA-232 108
- EIA/TIA-449 111
- <— indicates DCE to DTE 114
- Multiport Serial Routers 123
- Safety Recommendations 124
- General Site Requirements 125
- Site Environment 126
- Preventive Site Configuration 126
- Configuring Equipment Racks 127
- Power Supply Considerations 127
- Installation Checklist 129
- Creating a Site Log 130
- Cabling Considerations 130
- Distance Limitations 131
- Console Port Connections 133
- Auxiliary Port Connections 133
- Ethernet Connections 134
- Token Ring Connections 134
- BRI Connections 136
- Inspecting the System 137
Relacionado con productos y manuales para Redes Cisco 2513
Redes Cisco Cisco 3900 series Manual de usuario
(11 paginas)
(11 paginas)
Redes Cisco WS-X4991 Manual de usuario
(15 paginas)
(15 paginas)
Redes Cisco WRT54GC Manual de usuario
(69 paginas)
(69 paginas)
Redes Cisco DPC 3925 Manual de usuario
(116 paginas)
(116 paginas)
Redes Cisco 2520-RF - 2520 Router Manual de usuario
(28 paginas)
(28 paginas)
Redes Cisco WMP54G Guía de usuario
(25 paginas)
(25 paginas)
Redes Cisco Ethernet switch Instrucciones de operaciones
(266 paginas)
(266 paginas)
Redes Cisco CB20A Información técnica
(24 paginas)
(24 paginas)
Redes Cisco 2610 - Router - EN Guía de instalación
(18 paginas)
(18 paginas)
Redes Cisco DPC3010 Manual de usuario
(40 paginas)
(40 paginas)
Redes Cisco WS-X4604-GWY - VoIP Gateway Especificaciones
(262 paginas)
(262 paginas)
Kenwood MFJ-286 manuales
Manuales del propietario y guías del usuario para Micrófonos Kenwood MFJ-286.
Ofrecemos 1 manuales en pdf Kenwood MFJ-286 para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales