Cisco CX-FEIP-2TX= Installation and con?guration Especificaciones Pagina 278
- Pagina / 493
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
7-22
Cisco ONS 15454 Installation and Operations Guide, R3.2
March 2002
Chapter 7 Card Provisioning
Provisioning Optical Cards
NPJC-Pdet
Negative Pointer Justification
Count, STS Path detected. See the
“Enabling Pointer Justification
Count Parameters” section on
page 8-12 for more information.
Numeric. Defaults (Near and Far End):
Line
• 0 (15 minutes)
• 0 (1 day)
PPJC-Pgen
Positive Pointer Justification
Count, STS Path generated. See
the “Enabling Pointer Justification
Count Parameters” section on
page 8-12 for more information.
Numeric. Defaults (15 min/1 day):
Line
• 0/0 (Near and Far End)
NPJC-Pgen
Negative Pointer Justification
Count, STS Path generated. See
the “Enabling Pointer Justification
Count Parameters” section on
page 8-12 for more information.
Numeric. Defaults (15 min/1 day):
Line
• 0/0 (Near and Far End)
PSC
Protection Switching Count (Line) Numeric. Defaults (15 min/1 day):
Line
• 1/5 (Near End)
• 0/0 (Far End)
PSD
Protection Switch Duration (Line) Numeric. Defaults (15 min/1 day):
Line
• 300/600 (Near End)
• 0/0 (all OC-N cards, Far End)
PSC-W
Protection Switching Count -
Working line
BLSR is not supported on the
OC-3 card; therefore, the PSC-W,
PSC-S, and PSC-R PMs do not
increment.
Numeric. Defaults (15 min/1 day):
Line
• 0/0 (all OC-N cards except OC-3, Near and
Far End)
PSD-W
Protection Switching Duration -
Working line
BLSR is not supported on the
OC-3 card; therefore, the PSD-W,
PSD-S, and PSD-R PMs do not
increment.
Numeric. Defaults (15 min/1 day):
Line
• 0/0 (all OC-N cards except OC-3, Near and
Far End)
PSC-S
Protection Switching Duration -
Span
BLSR is not supported on the
OC-3 card; therefore, the PSC-W,
PSC-S, and PSC-R PMs do not
increment.
Numeric. Defaults (15 min/1 day):
Line
• 0/0 (all OC-N cards except OC-3, Near and
Far End)
Table 7-8 OC-N Card Threshold Settings on the Provisioning > Thresholds Tab (continued)
Heading Description Options
- Operations Guide 1
- CONTENTS 3
- Contents 10
- March 2002 10
- Hardware Installation 29
- Ethernet Operation 32
- Procedures 33
- About This Manual 35
- Related Documentation 36
- Conventions 37
- Obtaining Documentation 37
- World Wide Web 38
- Ordering Documentation 38
- Documentation Feedback 38
- Cisco.com 39
- Technical Assistance Center 39
- Cisco TAC Escalation Center 39
- 1.1 Installation Overview 42
- 1.2 Installation Equipment 43
- 1.2.1 Included Materials 44
- 1.3 Rack Installation 45
- Rack Installation 46
- 1.3.2 Mounting a Single Node 47
- Equipment rack 48
- Universal 48
- (reversible) 48
- 1.4 Front Door Access 51
- Front Door Access 52
- Open the door 53
- 1.5 Backplane Access 54
- 1.5.1 Lower Backplane Cover 55
- 1.5.2 Alarm Interface Panel 56
- 1.6 EIA Installation 57
- 1.6.2 High-Density BNC EIA 58
- 1.6.3 SMB EIA 59
- 1.6.4 AMP Champ EIA 60
- AMP CHAMP 61
- EIA Installation 62
- Fan-tray 67
- Power and Ground Installation 68
- FRAME GROUND 69
- Battery leads (red) 70
- Return leads (black) 70
- 1.9.1 Alarm Installation 72
- 1.9.2 Timing Installation 73
- 1.9.3 LAN Installation 74
- Coaxial Cable Installation 76
- DS-1 Cable Installation 79
- DS-1 Electrical Interface 81
- Adapter or balun 81
- Binder Group) (continued) 82
- 1.12 Card Installation 84
- 1.12.1 Slot Requirements 85
- Card Installation 86
- Cable Routing and Management 94
- Reversible jumper 95
- Fold down 95
- FAN FAIL 97
- Connector ends 98
- Tie-wrap 98
- Tie-wraps 98
- Screw locations 100
- 1.15 Ferrite Installation 101
- 1730-0730 for each cable 102
- January 2005 103
- Ferrite Installation 103
- 1.16.2 Slot Assignments 104
- 1.16.3 Cards 104
- 1.16.1 Bandwidth 104
- 1.16.4 Configurations 105
- 1.17 Installation Checklist 107
- Software Installation 111
- 2.2 Computer Requirements 112
- Computer Requirements 113
- Running the CTC Setup Wizard 114
- 2.4.2 Network Connections 117
- Logging into the ONS 15454 119
- Login node 120
- Login node group 120
- Step 5 Click OK 122
- 2.6.1 Node View 124
- 2.6.1.3 Node View Tabs 125
- 2.6.2 Network View 126
- 2.6.2.2 Network View Tasks 127
- 2.6.2.3 Creating Domains 128
- Table 2-8 Managing Domains 129
- Working with the CTC Window 130
- 2.6.3 Card View 132
- 2.7 CTC Navigation 133
- Moving the mouse 134
- ONS 15454 134
- 2.8 Viewing CTC Table Data 135
- Viewing CTC Table Data 136
- OC-N Cards 137
- DS-N Cards 137
- Procedure: Export CTC Data 139
- Node Setup 141
- Chapter 3 Node Setup 142
- Procedure: Create New Users 148
- Procedure: Edit a User 148
- Procedure: Delete a User 148
- Creating Protection Groups 149
- Procedure: Enable Ports 150
- Setting Up ONS 15454 Timing 152
- Viewing ONS 15454 Inventory 157
- Viewing CTC Software Versions 159
- IP Networking 161
- Chapter 4 IP Networking 162
- 15454s #2 and #3 164
- Procedure: Set up OSPF 172
- SONET Topologies 179
- 5.2.1 Two-Fiber BLSRs 180
- 5.2.2 Four-Fiber BLSRs 182
- 5.2.3 K3 Byte Remapping 185
- 5.2.4 BLSR Bandwidth 185
- Figure 5-9 A five-node BLSR 187
- Free Slot 188
- 5.2.6 Setting Up BLSRs 189
- Procedure: Remap the K3 Byte 192
- Procedure: Provision the BLSR 193
- Procedure: Add a BLSR Node 197
- Procedure: Remove a BLSR Node 200
- Figure 5-23 An OC-3 UPSR 207
- 5.3.2 Setting Up a UPSR 209
- Procedure: Add a UPSR Node 213
- 5.4 Subtending Rings 215
- 13 serve the UPSR 216
- Subtending Rings 217
- Linear ADM Configurations 220
- Path-Protected Mesh Networks 229
- Working traffic 230
- Circuits and Tunnels 233
- Creating Monitor Circuits 241
- 6.5 Searching for Circuits 242
- 6.6 Editing UPSR Circuits 242
- Editing UPSR Circuits 243
- 6.7 Creating a Path Trace 244
- Creating a Path Trace 245
- Cross-Connect Card Capacities 247
- 6.8.1 VT1.5 Cross-Connects 248
- 6.8.2 VT Tunnels 251
- 6.9 Creating DCC Tunnels 253
- Creating DCC Tunnels 254
- Card Provisioning 257
- Provisioning Electrical Cards 258
- 7.2.1 DS-1 Card Parameters 259
- 7.2.2 DS-3 Card Parameters 262
- 7.2.3 DS3E Card Parameters 264
- 7.2.5 EC1-12 Card Parameters 270
- Provisioning Optical Cards 274
- 7.4 Provisioning IPPM 280
- Provisioning IPPM 281
- 7.5.1 Using Virtual Wires 282
- Step 5 Click Apply 286
- Performance Monitoring 291
- 8.1.1 Viewing PMs 292
- Near End and Far End buttons 295
- Signal-type menus 296
- Baseline button 297
- 8.1.6 Using the Clear Button 298
- 8.2 Changing Thresholds 299
- STS FC-P 316
- STS SES-P 316
- STS UAS-P 316
- 9.1.1 G1000-4 Application 342
- G1000-4 Card 343
- 9.1.5 G1000-4 LEDs 345
- FAIL LED 346
- ACT/LINK LED 346
- 9.2 E Series Cards 349
- 9.2.1 E100T-12/E100T-G Card 350
- 9.2.2 E1000-2/E1000-2-G Card 350
- 9.2.3 E Series LEDs 350
- E Series Cards 351
- Table 9-4 Available GBICs 352
- 6. STS 3c +STS 3c + 6 STS-1s 354
- 7. 12 STS-1s 354
- Figure 9-17 Viewing a span 362
- Step 31 Click Finish 362
- ONS NodeONS Node 365
- SONET/SDH 365
- Ethernet 365
- Point-to-Point Circuit 371
- ONS Node ONS Node 371
- 9.6 E Series VLAN Support 376
- Data Flow 377
- E Series VLAN Support 379
- Redundant path (blocked) 380
- Primary path (forwarding) 380
- Step 4 Click Apply 381
- 9.8.1.1 Statistics Window 383
- 9.8.1.2 Utilization Window 385
- 9.8.1.4 History Window 386
- 9.8.3.1 Statistics Window 387
- 9.8.3.4 History Window 388
- 9.8.4.1 MAC Table Window 389
- 10.1 Overview 395
- Viewing ONS 15454 Alarms 396
- Table 10-3 Alarm Display 397
- 10.2.3 Conditions Tab 399
- 10.2.4 Viewing History 401
- 10.3 Alarm Profiles 402
- Alarm Profiles 403
- 10.3.1.1 Alarm Profile Menus 404
- 10.3.1.4 Row Display Options 405
- 10.4 Suppressing Alarms 408
- Suppressing Alarms 409
- 11.1 SNMP Overview 411
- 11.2 SNMP Basic Components 412
- 11.3 SNMP Support 413
- Chapter 11 SNMP 414
- SNMP Support 414
- Table 11-1 SNMP Message Types 415
- 11.5 SNMP Traps 416
- SNMP Traps 417
- 11.6 SNMP Community Names 419
- 11.7.4 Alarm Group 420
- 11.7.5 Event Group 420
- Circuit Routing 421
- Secondary Sources and Drops 422
- Manual Circuit Routing 423
- Regulatory Compliance 429
- Japan Approvals 430
- Korea Approvals 432
- Installation Warnings 433
- DC Power Connection Warning 435
- Class 1 Laser Product Warning 438
- Restricted Area Warning 439
- Ground Connection Warning 440
- Qualified Personnel Warning 441
- More Than One Power Supply 442
- Unterminated Fiber Warning 443
- Laser Activation Warning 445
- Numerics 447
- Acronyms 448
- Glossary 462
Relacionado con productos y manuales para Redes Cisco CX-FEIP-2TX= Installation and con?guration
Redes Cisco 1710 Información técnica
(26 paginas)
(26 paginas)
Redes Cisco MC16E Especificaciones
(19 paginas)
(19 paginas)
Redes Cisco WMA11B Guía de usuario
(2 paginas)
(2 paginas)
Redes Cisco 7600-ES20-GE3CXL-RF - Ethernet Services 20G Line Card Switch Manual de usuario
(398 paginas)
(398 paginas)
Redes Cisco 678 Especificaciones
(192 paginas)
(192 paginas)
Redes Cisco ONS 15327 Manual de usuario
(11 paginas)
(11 paginas)
Redes Cisco 820 Series Guía de instalación
(16 paginas)
(16 paginas)
Redes Cisco PIX-515E Guía de instalación
(20 paginas)
(20 paginas)
Redes Cisco WRT300N Guía de usuario
(90 paginas)
(90 paginas)
Redes Cisco 12000 GSR Manual de usuario
(17 paginas)
(17 paginas)
Redes Cisco WS-C2916M-XL Manual de usuario
(20 paginas)
(20 paginas)
Redes Cisco 15216 EDFA2 Especificaciones
(280 paginas)
(280 paginas)
Redes Cisco uBR10-LCP2-MC28C Especificaciones
(32 paginas)
(32 paginas)
Redes Cisco 4430 Manual de usuario
(12 paginas)
(12 paginas)
Redes Cisco MGX 8230 Especificaciones
(282 paginas)
(282 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.081 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales