Cisco Wireless Express 526 Guía de usuario

QUICK START GUIDE Cisco 526 Wireless Express Mobility ControllerINCLUDING LICENSE AND WARRANTY1 About this Guide2 Overview3 Unpacking and Preparing t

10 WLAN SSID The network name, or service set identifier (SSID). This is the default SSID that the access points use when they join a controller.RADIU

11 To use the controller’s startup wizard, you will need an Ethernet-capable PC running Windows XP and an Ethernet cable. The controller’s default IP

12 Step 9 Confirm your password in the Confirm Password field.Step 10 Click Next. The Management Interface Configuration screen appears (See Figure 4)

13 Figure 5 Miscellaneous Configuration Screen

14 Step 15 Optional, choose the LWAPP Transport Mode (Layer 3 default).Step 16 Enter the RF mobility domain name.Step 17 Check your country code.Step

15 Figure 7 Virtual Interface Configuration ScreenStep 24 Enter the virtual interface IP address. Default is 1.1.1.1 (a non-valid IP address).Step 25

16 Figure 9 RADIUS Server Configuration ScreenStep 31 Optional, enter the RADIUS server configuration information.Step 32 If you have configured RADIU

17 Figure 11 Configuration Wizard Completed ScreenStep 36 Click the Save And Reboot button to save your configuration. Note Click the Back button to r

18 6 Mounting the WLC526 ControllerThe WLC526 controller can be mounted as follows:• On a horizontal or vertical surface such as a desktop or shelf.

19 Figure 12 WLC526 Bottom PlateNote You must provide the hardware necessary to mount the controller securely and safely. 1Rubber pads3Keyhole slots2A

2 1 About this GuideThis guide will help you install the Cisco 526 Series Wireless Express Mobility Controller (hereafter referred to as the WLC526 o

20 Caution When vertically mounting your controller, you must mount the controller with its front panel facing down (towards the floor) unless you are

21 7 In Case of DifficultyChecking the Controller LEDsIf your controller is not working properly, check the LEDs on the front panel of the unit. You

22 Using the Reset ButtonThe Reset button on the controller’s front panel becomes active after the controller boots. You can use the Reset button to r

23 Step 3 When the Alarm LED turns green, release the Reset button by removing the paper clip.Step 4 The controller power cycles and reboots. The cont

24 3. To read translated and localized warranty information about your product, follow these steps:a. Enter this part number in the Warranty Document

25 9 Translated WarningsStatement 1071—Warning DefinitionWarningIMPORTANT SAFETY INSTRUCTIONSThis warning symbol means danger. You are in a situation

26 AttentionIMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entra

27 AdvarselVIKTIGE SIKKERHETSINSTRUKSJONERDette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å

28 Varning!VIKTIGA SÄKERHETSANVISNINGARDenna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du ut

29

3 WarningThere is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommende

30

31

32

33 Statement 1015—Battery HandlingWarningThere is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the sa

34 ¡Advertencia!Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la batería exclusivamente con el mismo tipo o

35 Statement 1024—Ground ConductorWarningThis equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of

36 AdvarselDette utstyret må jordes. Omgå aldri jordingslederen og bruk aldri utstyret uten riktig montert jordingsleder. Ta kontakt med fagfolk innen

37

38 Statement 1040—Product DisposalWarningUltimate disposal of this product should be handled according to all national laws and regulations. Statement

39 AvvertenzaLo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.AdvarselEndelig kassering av dette produktet

4 • Standards-based enterprise-class security • Simplified network deployment and management with automated radio resource features• Centralized manag

40 Statement 371—Power Cable and AC Adapter - Japan

41

42

43

Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0

5 • Cisco Unified Communications 500 Series for Small Business Getting Started Guide—Provides basic installation and setup instructions for the Cisco

6 Package ContentsEach WLC526 controller package contains the following items:• One Cisco 526 wireless LAN controller• One power cord• One Ethernet ca

7 Choosing a Physical LocationYou can install the controller on a horizontal or vertical surface. The controller’s bottom plate has two keyhole slots

8 Table 1 Startup Wizard Information Wizard Setting ActionSystem Name The name you want to assign to the controller. You can enter up to 32 ASCII char

9 Configured Country Code The country for which the controller is configured. This setting is not changeable in the startup wizard.Regulatory Domain T