Cisco SLM2008 - Small Business Smart Switch Información técnica Pagina 164
- Pagina / 202
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring IP Information
Configuring ARP
Cisco Small Business 200 Series Smart Switch Administration Guide 157
15
Configuring ARP
The switch maintains an ARP (Address Resolution Protocol) Table for all the known
devices that reside in its directly connected IP subnets. A directly connected IP
subnet is the subnet that a IPv4 interface of the switch is connected to. When the
switch needs to send/route a packet to a local device, it searches the ARP Table to
obtain the MAC address of the device. The ARP Table contains both static and
dynamic addresses. Static addresses are manually configured and do not age out.
The switch creates dynamic addresses from the ARP packets it receives. Dynamic
addresses age out after a configured time.
The ARP Table Page enables viewing dynamic ARP entries that the switch has
learned, changing the ARP entry aging time, clearing ARP entries, and adding or
deleting static ARP entries.
NOTE The IP/MAC address mapping information in the ARP Table is used by the switch to
forward traffic originated by the switch.
To define the ARP tables:
STEP 1 Click IP Configuration > ARP. The ARP Table Page opens.
STEP 2 Enter the parameters.
• ARP Entry Age Out—Enter the number of seconds that dynamic addresses
can remain in the ARP Table. A dynamic address ages out after the time it is
in the table exceeds the ARP Entry Age Out time. When a dynamic address
ages out, it is deleted from the table, and needs to be relearned to be entered
into the table again.
• Clear ARP Table Entries—Select the type of ARP entries to be cleared the
system.
-
All
—Deletes all of the static and dynamic addresses immediately.
-
Dynamic
—Deletes all of the dynamic addresses immediately.
-
Static
—Deletes all of the static addresses immediately.
-
Normal Age Out
—Deletes dynamic addresses based on the configured
ARP Entry Age Out time.
The ARP Table displays the following fields:
• Interface—The IPv4 Interface of the directly connected IP subnet where the
IP device resides.
- Cisco Small Business 1
- ADMINISTRATION 1
- Contents 2
- Chapter 1: Getting Started 1 2
- Chapter 5: System Time 55 3
- Getting Started 8
- Logging In 9
- Password Expiration 10
- Logging Out 10
- Login Page 11
- Application Header 12
- Management Buttons 14
- Viewing Statistics 16
- Viewing Etherlike Statistics 17
- Viewing 802.1X EAP Statistics 19
- Managing RMON Statistics 20
- Managing System Logs 23
- Setting System Log Settings 24
- Remote Log 25
- Servers Page 25
- Add Remote Log Server Page 25
- Remote Log Servers Page 25
- Viewing Memory Logs 26
- Flash Memory 27
- Managing System Files 28
- Language Files 34
- Copying Configuration Files 38
- DHCP Auto Configuration Page 39
- Auto Configuration Page 40
- System Time 41
- System Time Options 42
- Configuring System Time 43
- Adding an SNTP Server 45
- Add SNTP Server Page 46
- Defining SNTP Authentication 48
- Operations 49
- Security > TCP/UDP 50
- Services 50
- System Information 51
- Switch Models 52
- Rebooting the Switch 53
- Health Page 54
- Idle Session Timeout 54
- Pinging a Host 55
- Configuring Discovery 57
- Configuring LLDP 58
- Setting LLDP Properties 59
- Editing LLDP Port Settings 60
- LLDP Properties Page 61
- LLDP MED Protocol 62
- LLDP MED Network Policy Page 63
- LLDP MED Port Settings Page 64
- Displaying LLDP Port Status 65
- Local Information Page 67
- Neighbors Information Page 70
- Accessing LLDP Statistics 74
- LLDP Overloading 75
- Size (Bytes) 77
- Port Management 78
- Configuring Ports 80
- Configuring Link Aggregation 82
- Defining LAG Management 84
- Configuring LAG Settings 85
- Configuring LACP 86
- LACP Page 87
- Edit LACP Page 87
- Green Ethernet 88
- Managing Device Diagnostics 92
- Cable Extended Feature Page 93
- Optical Module Status Page 95
- Port and 96
- VLAN Mirroring Page 96
- Add Port/VLAN Mirroring 97
- Viewing CPU Utilization 98
- PoE on the Switch 99
- PoE Operation 100
- Configuring PoE Properties 101
- PoE Properties Page 102
- PoE Settings Page 103
- VLAN Management 105
- Default VLAN Settings 108
- Creating VLANs 109
- Interface Settings Page 110
- Defining VLAN Membership 112
- Configuring VLAN to Port 113
- Viewing VLAN Membership 114
- Voice VLAN 115
- Voice VLAN Options 116
- Voice VL AN 117
- Voice VLAN Properties Page 118
- Voice VLAN Properties 118
- Configuring Telephony OUI 119
- STP Flavors 120
- STP Status and 121
- Global Settings Page 121
- STEP 3 Enter the parameters 123
- Edit Rapid Spanning Tree Page 125
- Managing MAC Address Tables 128
- Dynamic MAC Addresses 129
- Querying Dynamic Addresses 130
- Multicast Forwarding 132
- Typical Multicast Setup 133
- Multicast Operation 133
- Multicast Registration 134
- Defining Multicast Properties 135
- STEP 2 Enter the parameters 136
- Adding MAC Group Address 137
- Add MAC Group Address 138
- Configuring IGMP Snooping 140
- IGMP Snooping Page 141
- Edit IGMP Snooping Page 141
- MLD Snooping 143
- MLD Snooping Page 144
- Edit MLD Snooping Page 144
- MAC Group Address Page 146
- Multicast Router Port Page 147
- Forward All Page 148
- Unregistered Multicast Page 149
- Configuring IP Information 151
- Management and IP Interfaces 152
- IP Addressing 153
- Defining an IPv4 Interface 153
- Administration 154
- File Management 154
- DHCP Auto Configuration 154
- Defining an IPv6 Interface 155
- Defining IPv6 Addresses 156
- Delay Time 158
- Configuring IPv6 Tunnels 159
- Modifying an IPv6 Neighbor 162
- Viewing IPv6 Route Tables 163
- Configuring ARP 164
- Domain Name Systems 165
- Defining DNS Servers 166
- Mapping DNS Hosts 167
- Configuring Security 169
- Defining Users 170
- Configuring RADIUS Parameters 172
- Defining Access Profiles 175
- STEP 5 Enter the parameters 177
- Defining Profile Rules 178
- STEP 4 Enter the parameters 179
- Configuring TCP/UDP Services 180
- Defining Storm Control 181
- Configuring Port Security 182
- Configuring 802.1X 184
- 802.1X Parameters Workflow 185
- Defining 802.1X Properties 186
- Viewing Authenticated Hosts 190
- QoS Features and Components 191
- Configuring QoS 192
- Configuring QoS Queues 194
- Queue Page 195
- CoS/802.1p to Queue Page 196
- Mapping DSCP to Queue 197
- Configuring Bandwidth 198
- Managing QoS Statistics 200
- , Cisco Stackpower 202
Relacionado con productos y manuales para Software Cisco SLM2008 - Small Business Smart Switch
Software Cisco SF 200-24P Información técnica
(277 paginas)
(277 paginas)
Software Cisco IAD2431-1T1E1 Manual de usuario
(7 paginas)
(7 paginas)
Software Cisco Small Business 300 Información técnica
(326 paginas)
(326 paginas)
Software Cisco 2950 - Catalyst Switch Especificaciones
(674 paginas)
(674 paginas)
Software Cisco 2924C - Catalyst Switch Especificaciones
(360 paginas)
(360 paginas)
Software Cisco Aironet 1200 Series Especificaciones
(364 paginas)
(364 paginas)
Software Cisco ROUTER-SDM-CD Guía de instalación
(6 paginas)
(6 paginas)
Software Cisco ROUTER-SDM-CD Guía de usuario
(20 paginas)
(20 paginas)
Software Cisco HWIC Guía de instalación
(82 paginas)
(82 paginas)
Software Cisco Aironet 700 Series Especificaciones
(402 paginas)
(402 paginas)
Software Cisco Catalyst 2900 Series XL Especificaciones
(322 paginas)
(322 paginas)
Software Cisco ROUTER-SDM-CD Guía de usuario
(74 paginas)
(74 paginas)
Software Cisco IAD2431-1T1E1 Manual de usuario
(12 paginas)
(12 paginas)
Software Cisco UC520-24U-8FXO-K9 Manual de usuario
(18 paginas)
(18 paginas)
Software Cisco LightStream 1010 Especificaciones
(89 paginas)
(89 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales