Cisco 3745 Guía de instalación

Quick Start GuideCisco 3745 RouterINCLUDING LICENSE AND WARRANTY1 Cisco 90-Day Limited Hardware Warranty Terms2 Documents, Equipment, and Tools3 Insta

10Installing the ChassisYou can set the chassis on a desktop or install it in a rack. See the applicable instructions in the following sections:• Rack

11Figure 2 Bracket Installation—Rear Panel ForwardFigure 3 Bracket Installation—Rear Panel Forward, Center-Mount RackNote The brackets can also be ins

12Grounding the ChassisYou must connect the chassis to a reliable earth ground; the ground wire must be installed in accordance with local electricals

134 Connect CablesWarningDo not work on the system, or connect or disconnect cables during periods of lightning activity. Statement 1001Caution To com

14Connecting Routers to DC PowerIf your router has a DC-input power supply, follow the directions in this section for proper wiring.WarningThis produc

15Tip Secure all power cabling when installing this unit to avoid disturbing field-wiring connections.Step 2 Strip the wires to the appropriate length

16Connecting Routers to the Cisco Redundant Power SystemIf your router uses the Cisco Redundant Power System (RPS), refer to the Cisco RPS Hardware In

175 Power Up the RouterChecklist for Power-UpYou are ready to power on the Cisco router if the following steps are completed:• The chassis is securely

18Messages begin to appear in your terminal emulation program window.Caution Do not press any keys on the keyboard until the messages stop. Any keys p

19Initial Configuration Using Cisco Router and Security Device ManagerIf the following messages appear at the end of the startup sequence, Cisco Route

21 Cisco 90-Day Limited Hardware Warranty TermsThere are special terms applicable to your hardware warranty and various services that you can use duri

20Step 3 Enter a host name for the router (this example uses 3745):Configuring global parameters: Enter host name [Router]: 3745The enable secret is

21Step 11 After the following messages appear, press Return to save the basic configuration:The following configuration command script was created:hos

22Step 1 To proceed with manual configuration using the CLI, enter no.Would you like to enter the initial configuration dialog? [yes/no]: noStep 2 Pre

23If double-width network modules are installed, the network module slots are numbered as follows:• 2 for the lower double-width slot• 4 for the upper

24Voice Interface NumberingVoice interfaces are numbered differently from the WAN interfaces described in the previous section. Voice interfaces arenu

25Ordering DocumentationYou can find instructions for ordering documentation at this URL:http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htmYou c

26To open a service request by telephone, use one of the following numbers:Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)EMEA: +32 2 704 55

27

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-

32 Documents, Equipment, and ToolsUser DocumentationAll the documents described here are available online on Cisco.com. To be sure of obtaining the la

43 Install ChassisSafety InformationFor safety information you need to know before working on your Cisco router, refer to the Cisco 2600 Series, Cisco

5WarnungWICHTIGE SICHERHEITSANWEISUNGENDieses Warnsymbol bedeutet Gefahr.Siebefindensichin einer Situation,diezu einer Körperverletzungführen könnte.

6

7AvisoINSTRUÇÕES IMPORTANTES DE SEGURANÇAEste símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesõescorporais.

8

9WarningThis unit is intended for installation in restricted access areas. A restricted access area can be accessed onlythrough the use of a special t