Cisco NPE-175 Especificaciones descargar pdf (Pagina 38)

1-38

Cisco 7200 VXR Installation and Configuration Guide

78-5469-04 B0

Chapter 1 Cisco 7200 VXR Product Overview

Field-Replaceable Units

LED Descriptions

All I/O controllers have LEDs, and the NPE-G1 also has interfaces that have LEDs.

The I/O controller faceplate contains LEDs that indicate system and port status; two additional LEDs

indicate the status of the Flash Disk or Flash memory cards installed in either PC Card slot. A CPU reset

button is located next to the IO POWER OK LED or next to the auxiliary port on the I/O controller

faceplate. The CPU reset button resets the entire system.

The NPE-G1 faceplate contains LEDs that indicate system and port status. The RJ-45 and GBIC ports

share the same LINK LED because only one of these ports per interface (0/1, 0/2, or 0/3) can be used at

any one time. The ENABLE LED is on if the RJ-45 port is in use. The POWER ON LED is on when the

system is powered on, whether or not an I/O controller is in the system with the NPE-G1.The SLOT

ACTIVE LED is on if there is a CompactFlash Disk in the NPE-G1.

Table 1-21 I/O Controller Memory Components

Type Size Quantity Memory Description Model Location

Boot ROM

1. The C7200-I/O-GE+E and C7200-I/O-2FE/E do not have a boot ROM component.

256 KB 1 32-pin DIP-type C7200-I/O-FE-MII U20

32-pin DIP-type or

32-pin PLCC-type

C7200-I/O-FE,

C7200-I/O

U20 or U4

Flash memory 4 MB 1 Contains the default

boot helper image

C7200-I/O-FE-MII U99

C7200-I/O-FE,

C7200-I/O

U99

U10, U11,

U12, and U13

(soldered)

2. Some I/O controllers have no Flash SIMM but use a permanently soldered 4-MB or 8-MB Flash memory chip instead. (For

the location of the 4-MB Flash memory chip, see the second illustration in Figure 1-16 and Figure 1-18. For the location of

the 8-MB Flash memory chip, see Figure 1-14 and Figure 1-15.)

8 MB 1 C7200-I/O-GE+E,

C7200-I/O-2FE/E

U13 and U25

(soldered)

Flash memory

card

16 or

20 MB

Up to 2 Contains the default

Cisco IOS image

All models PCCardslot 0

and slot 1

Flash Disk 32, 48, or

128 MB

Up to 2

NVRAM 128 KB 1 Nonvolatile EPROM

for the system

configuration file

C7200-I/O-FE-MII U41

C7200-I/O-FE,

C7200-I/O

U41

U14

(soldered)

3. The NVRAM on some I/O controllers is replaced by a 32-pin nonsocketed SRAM component that is soldered onto the card.

The SRAM component is made to act like the NVRAM by the addition of some external components, oneof which is a 1-inch

(2.54-cm) button-type lithium battery.

C7200-I/O-GE+E,

C7200-I/O-2FE/E

U19

(soldered)

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 57 58

Comentarios a estos manuales

Sin comentarios

Cisco NPE-175 Especificaciones Pagina 38

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Cisco NPE-175