Cisco 15454-TCC - Network Processor Card Especificaciones Pagina 55
- Pagina / 334
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
1-21
Cisco ONS 15454 Troubleshooting and Maintenance Guide
November 2001
Chapter 1 Alarm Troubleshooting
Step 5 If the software reset does not clear the card, physically reseat the TCC+ card to perform a card pull.
Step 6 If the alarm still does not clear, replace the TCC+ card.
Note When you replace a card with an identical type of card, you do not need to make any changes
to the database.
1.3.29 CONTBUS-B-18
• Major, Non-service affecting
The main processor on the TCC+ card in Slot 11 lost communication with the coprocessor on the TCC+
card in Slot 7. The problem is with the physical path of communication from the TCC+ card to the
reporting TCC+ card. The physical path of communication includes the two TCC+ cards and the
backplane.
Caution Always use the supplied electrostatic discharge wristband when working with a powered ONS 15454.
Plug the wristband cable into the ESD jack located on the lower-right outside edge of the shelf
assembly.
Procedure: Clear the CONTBUS-B-18 Alarm on the TCC+ Card
Step 1 Position the cursor over the TCC+ card in Slot 11.
Step 2 Right-click and choose RESET CARD to make the TCC+ in Slot 11 the active TCC+ card.
Step 3 Wait approximately 2 minutes for the TCC+ in Slot 7 to reset as the standby TCC+ card.
Step 4 Position the cursor over the TCC+ card in Slot 7.
Step 5 Right-click and choose RESET CARD again to make the TCC+ in Slot 11 the active TCC+ card.
Step 6 If the alarm reappears when the TCC+ in Slot 11 reboots as the active TCC+, the TCC+ card in Slot 11
is defective and must be replaced.
Note When you replace a card with an identical type of card, you do not need to make any changes
to the database.
1.3.30 CTNEQPT-PB1PROT
• Critical, Service affecting
An Interconnection Equipment Failure - Standby Payload Bus alarm occurs when digital traffic is being
lost between the cross-connect (XC/XCVT/XC10G) card and the reporting traffic card.
- Maintenance Guide 1
- CONTENTS 3
- 2 General Troubleshooting 2-1 9
- 3 Maintenance 3-1 10
- Contents 11
- November 2001 11
- 4 Card Reference 4-1 12
- Alarm Troubleshooting 23
- Procedures 24
- About This Manual 29
- Related Documentation 30
- Conventions 30
- Obtaining Documentation 31
- Cisco.com 32
- Technical Assistance Center 32
- Cisco TAC Web Site 33
- Cisco TAC Escalation Center 33
- 1.2 Trouble Notifications 37
- 1.3 Alarm Procedures 38
- 1.3.3 AIS-P 39
- 1.3.4 AIS-V 39
- 1.3.5 APSB 40
- 1.3.6 APSCDFLTK 40
- 1.3.7 APSC-IMP 41
- 1.3.8 APSCINCON 42
- 1.3.9 APSCM 42
- 1.3.10 APSCNMIS 43
- 1.3.11 APSCONNL 44
- 1.3.12 APSMM 45
- 1.3.13 AUTOLSROFF 45
- 1.3.14 AUTORESET 46
- 1.3.15 AUTOSW-AIS 46
- 1.3.22 BLSROSYNC 48
- 1.3.23 CARLOSS 49
- 1.3.24 CONCAT 50
- 1.3.25 CONNLOS 51
- 1.3.26 CONTBUS-A-X 52
- 1.3.27 CONTBUS-A-18 53
- 1.3.28 CONTBUS-B-X 54
- 1.3.29 CONTBUS-B-18 55
- 1.3.30 CTNEQPT-PB1PROT 55
- 1.3.31 CTNEQPT-PB1WORK 57
- 1.3.32 CTNEQPT-PBXPROT 58
- 1.3.33 CTNEQPT-PBXWORK 59
- 1.3.34 DATAFLT 61
- 1.3.35 DISCONNECTED 61
- 1.3.36 EOC 62
- 1.3.37 EQPT 64
- 1.3.38 E-W-MISMATCH 64
- 1.3.39 EXCCOL 66
- 1.3.40 EXERCISE-SPAN-FAIL 66
- 1.3.41 EXERCISE-RING-FAIL 66
- 1.3.42 EXT 66
- 1.3.43 FAILTOSW 67
- 1.3.44 FAILTOSW-PATH 67
- 1.3.45 FAILTOSWR 69
- 1.3.46 FAILTOSWS 70
- 1.3.47 FAN 71
- 1.3.48 FE-AIS 71
- 1.3.49 FE-DS1-MULTLOS 72
- 1.3.50 FE-DS1-SNGLLOS 72
- 1.3.51 FE-EQPT-FAIL-SA 72
- 1.3.52 FE-EQPT-NSA 73
- 1.3.53 FE-IDLE 73
- 1.3.54 FE-LOCKOUT 74
- 1.3.55 FE-LOF 74
- 1.3.56 FE-LOS 75
- 1.3.57 FEPRLF 75
- 1.3.58 FORCED-REQ 75
- 1.3.59 FRNGSYNC 76
- 1.3.60 FSTSYNC 76
- 1.3.61 HITEMP 76
- 1.3.62 HLDOVERSYNC 77
- 1.3.63 IMPROPRMVL 78
- 1.3.64 INCOMPATIBLE-SW 79
- 1.3.65 INVMACADR 79
- 1.3.66 LOCKOUT-REQ 80
- 1.3.67 LOF (DS-1) 80
- 1.3.68 LOF (DS3XM-6) 81
- 1.3.69 LOF (BITS) 82
- 1.3.70 LOF (EC-1) 83
- 1.3.71 LOF (OC-N) 84
- 1.3.72 LOP-P 84
- 1.3.73 LOP-V 86
- 1.3.74 LOS (DS-N) 87
- 1.3.75 LOS (BITS) 88
- 1.3.76 LOS (OC-N) 88
- 1.3.77 LOS (EC-1) 89
- 1.3.78 LPBKDS1FEAC 90
- 1.3.79 LPBKDS3FEAC 90
- 1.3.80 LPBKFACILITY (DS-N) 90
- 1.3.81 LPBKFACILITY (OC-N) 91
- 1.3.82 LPBKTERMINAL (DS-N) 91
- 1.3.83 LPBKTERMINAL (OC-N) 92
- 1.3.84 MANRESET 93
- 1.3.85 MANUAL-REQ 93
- 1.3.86 MEA 93
- 1.3.87 MEM-GONE 94
- 1.3.88 MEM-LOW 94
- 1.3.89 MFGMEM 95
- 1.3.90 NOT-AUTHENTICATED 96
- 1.3.91 PDI-P 97
- 1.3.92 PEER-NORESPONSE 98
- 1.3.93 PLM-P 98
- 1.3.94 PLM-V 99
- 1.3.95 PRC-DUPID 100
- 1.3.96 PWRRESTART 100
- 1.3.97 RAI 101
- 1.3.98 RCVR-MISS 101
- 1.3.99 RFI-L 101
- 1.3.100 RFI-P 102
- 1.3.101 RFI-V 102
- 1.3.102 RING-MISMATCH 103
- 1.3.103 SD-L 104
- 1.3.104 SD-P 104
- 1.3.105 SF-L 105
- 1.3.106 SF-P 106
- 1.3.107 SFTWDOWN 107
- 1.3.108 SFTWDOWN-FAIL 107
- 1.3.109 SQUELCH 108
- 1.3.110 SSM-FAIL 109
- 1.3.111 STU 109
- 1.3.112 SWTOPRI 109
- 1.3.113 SWTOSEC 110
- 1.3.114 SWTOTHIRD 110
- 1.3.115 SYNCPRI 110
- 1.3.116 SYNCSEC 111
- 1.3.117 SYNCTHIRD 111
- 1.3.118 SYSBOOT 112
- 1.3.119 TIM-P 112
- 1.3.120 TRMT 113
- 1.3.121 TRMT-MISS 113
- 1.3.122 UNEQ-P 114
- 1.3.123 UNEQ-V 115
- 1.4 DS3E Line Alarms 116
- General Troubleshooting 119
- Circuits and Timing 120
- Fiber and Cabling 120
- Power and LED Tests 120
- 2.2 Network Tests 121
- 2.2.3.1 FEAC Send Code 134
- 2.2.3.3 FEAC Alarms 135
- . The username or 139
- 2.3.10 DCC Connection Lost 140
- Procedure: Ping the ONS 15454 141
- 2.3.14 Ethernet Connections 142
- 2.4 Circuits and Timing 145
- 2.5 Fiber and Cabling 147
- Receiver Transmitter 149
- Class 1 laser product 150
- 2.5.3 Create CAT-5 Cables 151
- Figure 2-17 RJ-45 pin numbers 152
- 2.6 Power and LED Tests 154
- Maintenance 157
- 3.1.1 Reusable Air Filter 158
- 3.1.2 Disposable Air Filter 159
- Fan tray filter 160
- Fan tray 160
- Small engraved 160
- Chapter 3 Maintenance 162
- Fan-Tray Assembly Replacement 162
- 3.4 System Reset 164
- System Reset 165
- Database Backup and Restore 166
- 3.7 Card Replacement 170
- TCC Card to TCC+ Card Upgrade 171
- XC Card to XCVT Card Upgrade 173
- 3.12 Span Upgrades 178
- 3.12.1 Span Upgrade Wizard 179
- Span Upgrades 180
- 3.12.2 Manual Span Upgrades 181
- Procedure: Apply a Lock On 185
- Procedure: Apply a Lock Out 186
- 3.14.1 EIA Types 187
- Procedure: Install the EIAs 188
- 3.15 Fiber Cleaning 189
- 3.16 Powering Down a Node 189
- Procedure: Power Down a Node 190
- Card Reference 191
- 4.1.2 Electrical Cards 192
- 4.1.3 Optical Cards 193
- 4.1.4 Ethernet Cards 194
- Chapter 4 Card Reference 195
- Card Overview 195
- 0 to +55 degrees Celsius) 196
- 4.1.7 Card Compatibility 199
- 4.2.1 Protection, 1:1 202
- 4.2.2 Protection, 1:N 202
- 4.2.2.1 Revertive Switching 203
- 4.3.3 SMB Protection 204
- 4.4 Optical Card Protection 205
- 4.5 Unprotected Cards 206
- 4.6.3 TCC+ Specifications 209
- 4.7 XC Cross-Connect Card 210
- XC Cross-Connect Card 211
- 4.7.2 XC Specifications 212
- 4.8 XCVT Cross-Connect Card 213
- 4.8.1 VT Mapping 214
- 4.8.2 XCVT Hosting DS3XM-6 215
- 4.8.4 XC/XCVT Compatibility 216
- XC10G Cross-Connect Card 217
- 4.9.1 VT Mapping 218
- 4.9.2 XC10G Hosting DS3XM-6 219
- 4.10.1 User-Defined Alarms 221
- 4.10.2 Orderwire 222
- 4.10.3 AIC Specifications 223
- • Compliance 224
- 4.11 EC1-12 Card 225
- 4.11.1 EC1-12 Hosted by XCVT 226
- 4.11.4 EC1-12 Specifications 226
- EC1-12 Card 227
- 4.12 DS1-14 Card 228
- 4.12.1 DS1-14 Hosted by XCVT 229
- 4.12.4 DS1-14 Specifications 229
- DS1-14 Card 230
- 4.13 DS1N-14 Card 231
- DS1N-14 Card 232
- 4.14 DS3-12 Card 234
- 4.14.3 DS3-12 Specifications 235
- DS3-12 Card 236
- 4.15 DS3N-12 Card 237
- DS3N-12 Card 238
- 4.16 DS3-12E Card 240
- 4.16.3 DS3-12E Compatibility 241
- DS3-12E Card 242
- 4.17 DS3N-12E Card 243
- DS3N-12E Card 244
- 4.18 DS3XM-6 Card 246
- DS3XM-6 Card 247
- OC3 IR 4/STM1 SH 1310 Card 249
- 33678 12931 252
- OC12 IR/STM4 SH 1310 Card 253
- OC12 LR/STM4 LH 1310 Card 255
- OC12 LR/STM4 LH 1550 Card 258
- 4.23 OC48 IR 1310 Card 261
- OC48 IR 1310 Card 262
- 4.24 OC48 LR 1550 Card 264
- OC48 LR 1550 Card 265
- OC48 IR/STM16 SH AS 1310 Card 268
- OC48 LR/STM16 LH AS 1550 Card 271
- Red FAIL LED 274
- Green ACT LED 274
- Amber SF LED 274
- 4.28 OC48 ELR 200 GHz Cards 276
- OC48 ELR 200 GHz Cards 278
- OC192 LR/STM64 LH 1550 Card 279
- Class 1M (IEC) 280
- Class 1 (CDRH) 280
- 4.30 E100T-G Card 283
- E100T-G Card 284
- 4.30.3 E100T-G Compatibility 285
- 4.31 E1000-2-G Card 286
- E1000-2-G Card 288
- 4.32 E100T-12 Card 289
- E100T-12 Card 290
- 4.33 E1000-2 Card 292
- 4.33.3 E1000-2 Compatibility 294
- Numerics 295
- Acronyms 296
- Glossary 310
- VT layer 321
Relacionado con productos y manuales para Software Cisco 15454-TCC - Network Processor Card
Software Cisco WS-CBS3120X-S Especificaciones
(100 paginas)
(100 paginas)
Software Cisco ROUTER-SDM-CD Guía de usuario
(40 paginas)
(40 paginas)
Software Cisco ME 3400 Especificaciones
(872 paginas)
(872 paginas)
Software Cisco SIEMENS HICOM 330E Manual de usuario
(73 paginas)
(73 paginas)
Software Cisco UC520W-8U-4FXO-K9 Manual de usuario
(14 paginas)
(14 paginas)
Software Cisco IE 2000 Especificaciones
(336 paginas)
(336 paginas)
Software Cisco SIEMENS HICOM 330E Manual de usuario
(24 paginas)
(24 paginas)
Software Cisco LRE CPE Especificaciones
(648 paginas)
(648 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales