Cisco 2950 - Catalyst Switch Especificaciones descargar pdf (Pagina 335)

2-309

Catalyst 2950 and Catalyst 2955 Switch Command Reference

0L-10102-02

Chapter 2 Catalyst 2950 and 2955 Cisco IOS Commands

show controllers lre status

The Reed-Solomon errors show the number of errors detected and corrected in the data being received

on and sent from the switch LRE ports. Reed-Solomon errors are the result of noise exceeding the noise

margin. For short bursts of noise (such as motor power on or power surges), the interleaver prevents the

loss of Ethernet data packets. The number of Reed-Solomon errors then exceeds the number of Ethernet

CRC errors.

Note The Reed-Solomon errors are reset each time that you enter the show controllers lre status link

command.

The remote transmit power levels from the connected CPE devices might be different from each other,

depending on how long the cable is between the switch and the CPE device. A longer cable typically

causes the CPE device to send a higher signal to overcome the loss effects of distance.

The local receive-power rates actually displays the switch's adjustment to the incoming power level.

These numbers might be different from LRE port to LRE port, as the length of the cables to the CPE

devices might be different.

The interleaver columns display the interleaver block size for both directions of data. A higher

interleaver setting is less susceptible to certain kinds of impairments but can introduce a very small

amount of delay in the data path.

The PMD-S column refers to physical media dependent status and is provided as diagnostic information.

For more information about what can affect the LRE link and for the minimum required SNR ratios, see

the “LRE Links and LRE Profiles” section in the “Configuring LRE” chapter of the switch software

configuration guide for this release.

The sequence and sequence detail keywords display these status codes of profiles and sequences during

rate selection:

• Converged—Rate selection has converged on a profile.

• Locked—Rate selection has converged on a profile, and the port is locked to that profile.

• Executing—Rate selection is running on the port.

• Waiting on Link—No link is established.

• N/A—Sequence is not assigned to the port.

You can adjust the noise level during convergence by using the margin interface configuration

command.

Use the show controllers lre status cpe [interface-id] privileged EXEC command to display

information about a specific CPE port or all the CPE ports.

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output

do not appear, but the lines that contain Output appear.

Examples This is an example of output that shows link information for an LRE interface:

Switch# show controller lre status link longreachethernet0/2

Port Link SNR RS Errs CPE-Tx Sw-AGC-Gain Interleaver PMD-S

(dB) (dBm/Hz) (dB) Rx-Bsz Tx-Bsz

------ ---- ---- ----------- -------- ----------- ------------- -----

Lo0/2 UP 41 4829 - 57.7 - 7.6 16 16 0x04

1 2 ... 330 331 332 333 334 335 336 337 338 339 340 ... 673 674

Comentarios a estos manuales

Sin comentarios

Dewalt 621106-00 Bedienerhandbuch (44 Seiten)

Marke: Dewalt | Kategorie: Power tools | Größe: 2.97 MB |

Inhaltsverzeichnis

EWALT • www.dewalt.com

Important Safety Instructions

SAVE THESE INSTRUCTIONS

FEATURES (Fig. 1, 4)

Power Supply

Cutting Capacity

Vise Operation (Fig. 4)

Fence Operation

Depth Stop (Fig. 1)

Trigger Switch (Fig. 1)

(Fig. 7, 8)

EWALT for a free

Troubleshooting Guide

DOES NOT MAKE ACCURATE CUTS

CANNOT MOVE ARM

MATERIAL MOVES DURING CUT

Français

CONSERVER CES DIRECTIVES

Alimentation

Capacité de coupe

CARACTÉRISTIQUES (Fig. 1, 4)

Équipement standard

Transport (fig. 1)

Déverrouillage (fig. 1)

Utilisation du guide

(fig. 1)

Butée de profondeur (fig. 1)

Gâchette (Fig. 1)

EWALT (1-800-433-9258)

Guide de depannage

Instrucciones de seguridad

CONSERVE ESTAS INSTRUCCIONES

CARACTERÍSTICAS (FIG. 1, 4)

Alimentación eléctrica

Capacidad de corte

Equipo estándar

Para portar (Fig. 1)

Operación del torno (Fig. 4)

Operación de la guía

Tope de profundidad (Fig. 1)

EWALT (1-800

EWALT están cubiertas

EWALT, cualquiera sea

EWALT S.A. DE C.V

LA HERRAMIENTA NO ARRANCA

NO REALIZA CORTES PRECISOS

EL BRAZO ESTÁ FIJO

Weitere Produkte und Handbücher für Elektrowerkzeuge DeWalt

Modelle	Dokumententyp
DC385	Bedienerhandbuch DeWalt DC385 Instruction manual, 7 Seiten
36-485	Bedienerhandbuch DeWalt 36-485 Instruction manual, 53 Seiten
DCD710	Wartungshandbuch DeWalt DCD710 Technical data, 16 Seiten
DC490	Bedienerhandbuch DeWalt DC490 Instruction manual, 7 Seiten
36-085	Bedienerhandbuch DeWalt 36-085 Instruction manual, 19 Seiten
780	Wartungshandbuch DeWalt 780 Technical data, 19 Seiten
DW744	Bedienerhandbuch DeWalt DW744 Instruction manual, 44 Seiten
DW159	Bedienungsanleitung DeWALT, 8 Seiten
DW746X	Wartungshandbuch DeWalt DW746X Technical data, 128 Seiten
D25941	Wartungshandbuch DeWalt D25941 Technical data [en] , 15 Seiten
DC820	Wartungshandbuch DeWalt DC820 Technical data, 25 Seiten
D26414-XE	Bedienungsanleitung BIG BIG - Talair United Tools Pty Ltd, 5 Seiten
DCD776-XE	Bedienerhandbuch DeWalt DCD776-XE Instruction manual, 16 Seiten
DW006	Bedienerhandbuch DeWalt DW006 Instruction manual, 37 Seiten
DC547-XE	Bedienungsanleitung SRB Commercial Concreters Catalogue, 29 Seiten
DW997	Wartungshandbuch DeWalt DW997 Technical data, 116 Seiten
DW625E	Wartungshandbuch DeWalt DW625E Technical data, 100 Seiten
DCD980-XE	Wartungshandbuch DeWalt DCD980-XE Technical data, 40 Seiten
DCF813	Wartungshandbuch DeWalt DCF813 Technical data, 36 Seiten
DW892	Bedienerhandbuch DeWalt DW892 Instruction manual, 6 Seiten