Cisco 7200 VXR Manual de usuario Pagina 41

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 48
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 40
41
To connect a Cisco USB Flash memory module or the Aladdin USB eToken Pro key to the NPE-G2 USB port, simply insert the
module into the port as shown in Figure 23. The Flash memory module can be inserted in only one way, and can be inserted or
removed regardless of whether the router is powered up or not.
Caution Do not remove a USB Flash memory module when a read or write operation to the USB Flash memory module is
in progress. The router might reload, or the USB Flash memory module card can be damaged.
Note Only Cisco USB Flash memory modules and the Aladdin USB eToken Pro key are supported by Cisco routers.
Note For detailed information about the Cisco IOS commands that support USB Flash memory modules, see the USB Storage
document at
http://www.cisco.com/en/US/docs/ios/fundamentals/configuration/guide/usb_flash_keys_ps6922_TSD_Products_Confi
guration_Guide_Chapter.html#wp1027188
Replace a Port Adapter or Service Adapter
Figure 24 Replacing a Port Adapter
Note Before removing a port adapter, shut down the interface so that there is no traffic running through the port adapter
when it is removed.
Step 1 To remove a port adapter, place the port adapter lever in the unlocked position (2).
Note If you have difficulty installing a processing engine or I/O controller in the lowest slot of a Cisco 7200 VXR
router that is rack-mounted, remove the port adapters, processing engine and I/O controller from the chassis
and reinstall them. Install the processing engine and I/O controller in the lowest slots first, then populate the
slots above them, in a bottom-to-top order.
Step 2 Grasp the handle and pull the port adapter from the router, about halfway out of its slot (3). If you are removing a
blank port adapter, pull the blank port adapter completely out of the chassis slot.
1
Port adapter in place
4
Slot guide
2
Port adapter lever in unlocked position
5
Port adapter lever in locked position
3
Port adapter partially removed or installed
57037
2
0
4
1
3
5
6
FAST SERIAL
E
N
T
D
T
C
R
D
R
C
L
B
C
D
T
D
T
C
R
D
R
C
L
B
C
D
T
D
T
C
R
D
R
C
L
B
C
D
T
D
T
C
R
D
R
C
L
B
C
D
T
O
K
E
N
R
IN
G
0
1
2
3
Cisco 7200
Series
C
P
U
R
E
S
E
T
ENABLED
MII
EN
RJ45
EN
RJ45
LINK
1O PWR
OK
R
J
-
4
5
FA
ST ETH
ERN
ET
IN
PU
T/O
U
TPU
T CO
N
TRO
LL
ER
PCMCIA
EJECT
SLOT 0
SLOT 1
FE MII
E
N
A
B
L
E
D
M
II
L
IN
K
R
J
45
FAST ETHERNET
0
E
T
H
E
R
N
E
T
1
0
B
T
E
N
A
B
L
E
D
0
2
1
3
L
I
N
K
0
1
2
3
MII
EN
RJ45
EN
RJ45
LINK
1O PWR
OK
R
J
-
4
5
C
P
U
R
E
S
E
T
F
A
ST
E
T
H
E
R
N
E
T
IN
P
U
T
/O
U
T
P
U
T
C
O
N
T
R
O
L
L
E
R
ENABLED
PCMCIA
EJECT
SLOT 0
SLOT 1
FE MII
2
4
6
Cisco 7200
Series
1
3
5
E
T
H
E
R
N
E
T
1
0
B
T
E
N
A
B
L
E
D
0
2
1
3
L
I
N
K
0
1
2
3
E
N
A
B
L
E
D
M
II
L
I
N
K
R
J
4
5
FA
ST ETH
E
RN
ET
0
T
O
K
E
N
R
I
N
G
0
1
2
3
1
5
2
4
3
Vista de pagina 40
1 2 ... 36 37 38 39 40 41 42 43 44 45 46 47 48

Comentarios a estos manuales

Sin comentarios