Cisco XR 12000 Series Manual de usuario Pagina 111

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 148
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 110
2-81
Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide
OL-17438-04
Chapter 2 Overview: Cisco XR 12000 Series Router Shared Port Adapters
24-Port Channelized T1/E1/J1 ATM CEoP SPA Overview
RJ-45 Cable Pinouts
T1 lines from individual subscribers are attached to RJ-45 connectors on the front of the 24-port patch
panel. Each RJ-45 port accommodates an individual T1 subscriber line.
Pins 1 and 2 and 4 and 5 of the RJ-45 connectors are used for the 24-port CEoP SPAs Transmit (TX)
and Receive
(RX) signals. Depending on how the cable is installed between the SPA and its patch panel
(rear), the
RJ-45 connectors operate as follows:
If the TX cable lead is connected to Transmit on the patch panel and RX is connected to Receive:
The SPAs TX signals are transmitted on RJ-45 pins 1 (ring) and 2 (tip).
The SPAs RX signals are received on RJ-45 pins 4 (ring) and 5 (tip).
If the TX cable lead is connected to Receive on the patch panel and RX is connected to Transmit:
RJ-45 pins 1 and 2 are used for the SPAs RX signal.
RJ-45 pins 4 and 5 are used for the SPAs TX signal.
Patch Panel Cabling
If you are connecting two 24-Port Channelized T1/E1/J1 ATM CEoP SPAs to each other, you must cable
both SPAs patch panels together using a T1 cross-over cable or a T1 straight-through cable. The type of
cable you use (cross-over or straight-through) depends on how the CEoP SPAs are cabled to their patch
panels:
If both CEoP SPAs are connected to their patch panels in the same manner (TX to Transmit and
RX
to Receive, or TX to Receive and RX to Transmit), use a T1 cross-over cable to connect the
patch
panels to each other.
If both CEoP SPAs are connected to their patch panels in a different configuration (TX to Transmit
and RX to Receive on one SPA, and TX to Receive and RX to Transmit on the other SPA), use a
T1
straight-through cable (standard RJ-45 patch cable) between the patch panels.
24-Port Channelized T1/E1/J1 ATM CEoP SPA Patch Panel
The recommended patch panel is part number DCC2484/25T1S from SMP Data Communications
(
http://www.smpdata.com).
To order the patch panel, contact the Sales and Marketing Support staff at SMP Data Communications:
800-880-7674 (toll free in the U.S.A.)
828-298-2260 (outside the U.S.A.)
[email protected] (email)
Line 24 TX Tip
TX Ring
25
75
24
49
Not connected
RX Tip
RX Ring
49
99
Not connected 24
49
Table 2-50 24-Port Channelized T1/E1/J1 ATM CEoP SPA Cable Connector Pinouts (continued)
Subscriber Connector Pins
Line Signal SPA TX Cable Lead RX Cable Lead
Vista de pagina 110
1 2 ... 106 107 108 109 110 111 112 113 114 115 116 ... 147 148

Comentarios a estos manuales

Sin comentarios