Cisco XR 12404 Manual de usuario Pagina 141
- Pagina / 178
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5-17
Cisco XR 12404 Router Installation Guide
OL-13830-02
Chapter 5 Maintaining the Router
Removing and Replacing a DC Power Entry Module
Step 1 If the Input OK and Output OK LEDs are off, or if the Output Fail LED is on,
make sure that the:
• PEM is firmly seated in the bay and the captive screws are tightened securely.
• AC power source circuit breaker is switched on.
• Power cord is firmly plugged into the AC power source receptacle.
• Power cord is firmly plugged into the PEM and the bail latch is secure over
the plug.
• Power switch is set to the on (1) position.
Step 2 If the problem still exists after checking the items in Step 1, replace the PEM.
If replacing the PEM does not correct the proble
m, contact a Cisco service
representative for assistance.
Removing and Replacing a DC Power Entry Module
Although a DC PEM supports OIR, in order to maintain operational redundancy,
proper cooling, and meet EMI compliance standards, you must have both working
power supplies installed. When you remove a failed power supply with the router
in operation, perform the replacement as quickly as possible. Make sure you have
the tools and the replacement power supply ready before beginning the removal
and installation procedure.
Refer to Fi
gure 5-11 and use the following procedure to remove and replace a
DC PEM.
1 Input OK Green On The PEM is powered on and operating
co
rrectly.
2 Output OK Green On The AC power source is present and operating
wit
hin the specified limit.
3 Output Fail Amber On The PEM detects a fault condition causing it
to sh
utdown.
todd.book Page 17 Monday, March 16, 2009 2:47 PM
- March 2009 1
- CONTENTS 5
- 3 Installing the Router 3-1 6
- Contents 7
- Changes to This Document 9
- Audience 10
- Document Conventions 12
- Router Overview 15
- Route Processor 18
- 1 3 4 52 20
- BITS 1 AUX CONSOLE 22
- PRP-3 LEDs 23
- PRP Reset Switch 23
- PROCESSOR 24
- PRP Memory Components 26
- PRP SDRAM 30
- PRP SRAM 31
- PRP NVRAM 31
- PRP Flash Memory 31
- PRP-3 Compact Flash 32
- Supported Line Cards 33
- Q OC-3/STM-1 MM POS 34
- Q OC-3/STM-1 SM IR POS 34
- Alarm Functionality 35
- Power Source Monitoring 36
- Power Entry Modules 37
- Figure 1-12 AC PEM Components 38
- Fan Tray Assembly 40
- Figure 1-14 Fan Tray Assembly 41
- Cable Management System 42
- Maintenance Bus 45
- Code Download 46
- Diagnostics 46
- Preparing for Installation 47
- Safety and Compliance 48
- General Safety Guidelines 49
- Router Chassis 51
- Laser Safety 52
- Lifting Guidelines 52
- Safety with Electricity 54
- Rack Mounting Clearance 55
- Multiple Routers in a Rack 55
- 23.2657.761 56
- 18.95 in. 17.38 in 56
- Environmental Guidelines 57
- Temperature and Humidity 58
- Power Connection Guidelines 59
- Site Wiring 61
- Distance Limitations 62
- Site Preparation Checklist 63
- Installing the Router 66
- Required Tools 67
- Compliance 74
- Compliance (PRP-3 Installed) 75
- Figure 3-6 Cable Lug 75
- Figure 3-7 Crimping the Lug 76
- 1. Baud to 9600 80
- 2. Data bits to 8 80
- 3. Parity to no parity 80
- 4. Stop bits to 2 80
- PRP Console Port Signals 82
- PRP Auxiliary Port Signals 83
- PRP Ethernet Connections 86
- RJ-45 connector 87
- Figure 3-21 AC PEM LEDs 95
- Figure 3-22 DC PEM LEDs 96
- Figure 3-23 CSF LEDs 97
- Ta b l e 3-6 CSF LEDs 97
- Ta b l e 3-8 CSF MBus LEDs 97
- Manually Booting the System 98
- External Network Interface 98
- Identifying Startup Problems 100
- OL-13830-02 101
- Figure 4-1 AC PEM 104
- Figure 4-2 DC PEM and PDU 108
- Troubleshooting the RP 112
- ETH 1ETH 0 115
- Single PRP-3 Scenario 117
- PRP-3 Alphanumeric LEDs 117
- Dual PRP-3 Scenario 119
- Maintaining the Router 125
- Tools and Equipment 126
- Powering Off the Router 127
- CONSOLIDATED SWITCH FABRIC 128
- Step 12 Power on the PEM 140
- Step 12 Power on both PEMs 150
- Fabric Alarm 153
- Fabric Card 160
- Technical Specifications 163
- Product Architecture 164
- Specifications 165
- Compliance Information 167
- Ta b l e A-5 Immunity Tests 168
- FCC Class A Compliance 170
- CISPR 22 171
- Europe—EU 172
- VCCI Class A Notice for Japan 172
- Class A Notice for Hungary 173
- Class A Notice for Korea 174
- Numerics 175
Relacionado con productos y manuales para Hardware Cisco XR 12404
Hardware Cisco 3800 Series Manual de usuario
(138 paginas)
(138 paginas)
Hardware Cisco ACE XML OL-13877-01 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Cisco 3522 BRI Manual de usuario
(52 paginas)
(52 paginas)
Hardware Cisco WRV54GP2M Manual de usuario
(4 paginas)
(4 paginas)
Hardware Cisco OL-7822-06 Manual de usuario
(64 paginas)
(64 paginas)
Hardware Cisco 2100 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Cisco 8800 Manual de usuario
(24 paginas)
(24 paginas)
Hardware Cisco 3700 Series Manual de usuario
(78 paginas)
(78 paginas)
Hardware Cisco 1604 Manual de usuario
(22 paginas)
(22 paginas)
Hardware Cisco 1805 DOCSIS Manual de usuario
(4 paginas)
(4 paginas)
Hardware Cisco 1700 Manual de usuario
(88 paginas)
(88 paginas)
Hardware Cisco 10005 Manual de usuario
(20 paginas)
(20 paginas)
Hardware Cisco 7201 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Cisco 1700 Manual de usuario
(14 paginas)
(14 paginas)
Hardware Cisco 6.x and 7.0 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Cisco WIRELESS-G WRT54GP2 Manual de usuario
(112 paginas)
(112 paginas)
Hardware Cisco 12000 Manual de usuario
(60 paginas)
(60 paginas)
Hardware Cisco 6400 Manual de usuario
(54 paginas)
(54 paginas)
Hardware Cisco 1-PORT G.SHDSL 2600 Manual de usuario
(22 paginas)
(22 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.151 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales