Second-Generation Fast Ethernet Interface Processor (FEIP2) Installation and Configuration 35

Configuring the Fast Ethernet Interfaces

Checking the Conﬁguration

After conﬁguring the new interface, use the show commands to display the status of the new

interface or all interfaces and the ping command to check connectivity.

Using show Commands to Verify the FEIP2 Status

The following steps use show commands to verify that the new interfaces are conﬁgured and

operating correctly.

Step 1 Use the show version command to display the system hardware conﬁguration. Ensure

that the list includes the new interfaces.

Step 2 Display all the current interface processors and their interfaces with the show controllers

cbus command. Verify that the new FEIP2 appears in the correct slot.

Step 3 Specify one of the new interfaces with the show interfaces type slot/adapter/interface

command and verify that the ﬁrst line of the display speciﬁes the interface with the correct

slot number. Also verify that the interface and line protocol are in the correct state: up or

down.

Step 4 Display the protocols conﬁgured for the entire system and speciﬁc interfaces with the

show protocols command. If necessary, return to conﬁguration mode to add or remove

protocol routing on the system or speciﬁc interfaces.

Step 5 Display the running conﬁguration ﬁle with the show running-conﬁg command. Display

the conﬁguration stored in NVRAM using the show startup-conﬁg command. Verify

that the conﬁguration is accurate for the system and each interface.

If the interface is down and you conﬁgured it as up, or if the displays indicate that the hardware is

not functioning properly, ensure that the network interface is properly connected and terminated. If

you still have problems bringing the interface up, contact a service representative for assistance.

Using show Commands to Display Interface Information

To display information about a speciﬁc interface, use the show interfaces command with the

interface type and port address in the format show interfaces [type slot/adapter/port].

Following is a partial-display example of how the show interfaces command displays status

information (including the physical slot and port address) for the interface you specify. In this

example, most of the status information for each interface is omitted, and an FE interface in interface

processor slot 3 is shown:

Router# sh int fastethernet 2/0/0

FastEthernet2/0/0 is administratively down, line protocol is down

Hardware is cyBus FastEthernet Interface, address is 0000.0ca5.2380 (bia 0000)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255

Encapsulation ARPA, loopback not set, keepalive set (10 sec), hdx, 100BaseTX

(additional displayed text omitted from this example)

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 41 42

Comentarios a estos manuales

Sin comentarios

Legacy Car Audio LA-789 manuali

Manuali dei proprietari e guide per l'utente per Amplificatore per auto Legacy Car Audio LA-789.
We fornisce 1 manuali pdf Legacy Car Audio LA-789 per scaricare gratuitamente in base al tipo di documento: Manuale Utente

Modelli	Tipo di Documento
LA580	Manuale Utente Legacy Car Audio LA580 User Manual, 14 pagine
LA-1878	Manuale Utente Legacy Car Audio LA-1878 User Manual, 9 pagine
LA738	Manuale Utente Legacy Car Audio LA738 User Manual, 7 pagine

Cisco CX-FEIP-2TX= Installation and con?guration Especificaciones Pagina 35

Comentarios a estos manuales

Legacy Car Audio LA-789 manuali

Legacy car audio LA-789 Manuale Utente (14 pagine)

Indice

Più prodotti e manuali per Amplificatore per auto Legacy Car Audio

Cisco CX-FEIP-2TX= Installation and con?guration Especificaciones Pagina 35

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Cisco CX-FEIP-2TX= Installation and con?guration

Legacy Car Audio LA-789 manuali

Legacy car audio LA-789 Manuale Utente (14 pagine)

Indice

Più prodotti e manuali per Amplificatore per auto Legacy Car Audio