Cisco 4510R - Catalyst Switch Manual de usuario descargar pdf (Pagina 12)

Supervisor II Plus 10GE or Supervisor V 10GE

Catalyst 4500 Supervisor II Plus 10GE (WS−X4013+10GE) or Supervisor V 10GE (WS−X4516−10GE) has

four GE uplink interfaces and two 10 GE uplink interface per Supervisor. This table illustrates how the uplink

provides redundancy in a 4507R or 4510R Chassis in various combinations of the two supervisors in the

supervisor slots.

In Cisco IOS Software Release 12.2(25)SG and later on a Catalyst 4507R Series Switch, 10GE and GE

uplinks are concurrently usable on the Supervisor Engine V−10GE (WS−X4516−10GE) and the Supervisor

Engine II+10GE (WS−4013+10GE). In Cisco IOS Software Releases earlier than 12.2(25)SG, you need to

issue the hw−module uplink select configuration command to select either the 10GE or GE uplinks.

In Cisco IOS Software Release 12.2(25)SG and later, when you use a Supervisor Engine V−10GE

(WS−X4516−10GE) on a Catalyst 4510R Series Switch, you can select to use both the 10GE and GE uplinks

concurrently, but only with a WS−X4302−GB in slot 10. If either the 10GE or GE uplinks are selected, then

any linecard is allowed in slot 10. Issue the hw−module uplink select configuration command to select the

uplinks. In Cisco IOS Software Releases earlier than 12.2(25)SG, you cannot use the 10GE and GE uplinks

concurrently. The Cisco Catalyst 4000 NetFlow Services Card (WS−F4531) is an optional daughter card for

the Catalyst 4000/4500 Supervisor Engine IV or Supervisor Engine V. In the Supervisor Engine V−10GE, the

NetFlow functionality is embedded in the supervisor engine itself. It extends the functions of the supervisor

engine as it collects NetFlow statistics and enhanced Virtual LAN (VLAN) statistics without any affect on the

forwarding performance rates of the supervisor engine. The Catalyst 4500 series switches supports the

functionality of monitoring traffic in the same broadcast domain only when the 10GigE Supervisor is used. It

is not supported on the Supervisor Engine I, II, or III.

Note: Redundancy requires that both supervisor engines in the chassis are of the same supervisor engine

model, and to use the same Cisco IOS software image.

If only 10GE ports are selected for uplink:

Uplink

Interface

Slot 1:

Supervisor II

Plus 10GE or V

10 GE

Slot 2: Empty

Slot 1:Empty

Slot2:

Supervisor II

Plus 10GE or V

10 GE

Slot1:

Supervisor II

Plus 10GE or V

10 GE

Slot2:

Supervisor II

Plus 10GE or V

10 GE

10GE 1/1

Active N/A Active

10GE 1/2

Active N/A Not Active

10GE 2/1

N/A Active Active

10GE 2/2

N/A Active Not Active

If only GE ports are selected for uplink:

Uplink

Interface

Slot 1:

Supervisor II

Plus 10GE or V

10 GE

Slot 1:Empty

Slot2:

Supervisor II

Plus 10GE or V

Slot1:

Supervisor II

Plus 10GE or V

10 GE

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 20 21

Comentarios a estos manuales

Sin comentarios

Cisco 4510R - Catalyst Switch Manual de usuario Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Cisco 4510R - Catalyst Switch