Cisco Cisco Access Registrar 4.2 Especificaciones descargar pdf (Pagina 372)

100

101

7-62

Cisco Wireless LAN Controller Configuration Guide

OL-13826-01

Chapter 7 Controlling Lightweight Access Points

Configuring Country Codes

802.11BG :

Channels : 1 1 1 1 1

: 1 2 3 4 5 6 7 8 9 0 1 2 3 4

------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-

US (-AB) : A * * * * A * * * * A . . .

CA (-AB) : A * * * * A * * * * A . . .

MX (-NA) : A * * * * A * * * * A . . .

Auto-RF : C x x x x C x x x x C . . .

------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

802.11A : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6

: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5

------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

US (-AB) : . A . A . A . A A A A A * * * * * . . . * * * A A A A *

CA (-ABN) : . A . A . A . A A A A A * * * * * . . . * * * A A A A *

MX (-N) : . A . A . A . A A A A A . . . . . . . . . . . A A A A *

Auto-RF : . C . C . C . C C C C C . . . . . . . . . . . C C C C x

------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

Step 7 To save your settings, enter this command:

save config

Step 8 To see the countries to which your access points have been assigned, enter this command:

show ap summary

Information similar to the following appears:

Number of APs.................................... 2

AP Name Slots AP Model Ethernet MAC Location Port Country

-------- ------ ----------------- ----------------- ---------------- ------- --------

ap1 2 AP1030 00:0b:85:5b:8e:c0 default location 1 US

ap2 2 AIR-AP1242AG-A-K9 00:14:1c:ed:27:fe default location 1 US

Step 9 If you entered multiple country codes in Step 3, follow these steps to assign each access point to a

specific country:

a. Perform one of the following:

–

Leave the 802.11a and 802.11b/g networks disabled.

–

Re-enable the 802.11a and 802.11b/g networks and then disable only the access points for

which you are configuring a country code. To re-enable the networks, enter these commands:

config 802.11a enable network

config 802.11b enable network

To disable an access point, enter this command:

config ap disable ap_name

b. To assign an access point to a specific country, enter this command:

config ap country code {ap_name | all}

Make sure that the country code you choose is compatible with the regulatory domain of at least one

of the access point’s radios.

Note If you enabled the networks and disabled some access points and then run the config ap

country code all command, the specified country code is configured on only the disabled

access points. All other access points are ignored.

1 2 ... 367 368 369 370 371 372 373 374 375 376 377 ... 635 636

Comentarios a estos manuales

Sin comentarios

Cisco Cisco Access Registrar 4.2 Especificaciones Pagina 372

Comentarios a estos manuales