Cisco 6400 Guia de preparacion Pagina 12
- Pagina / 198
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
xii
Cisco 6400 Software Setup Guide
OL-1183-04
Preface
Audience
Audience
This guide is designed for the system administrator who will be responsible for setting up the CiscoIOS
software on the Cisco6400. The system administrator should be familiar with the installation of
high-end networking equipment.
This guide is intended primarily for the following audiences:
• Customers with technical networking background and experience
• Customers who support dial-in users
• System administrators who are familiar with the fundamentals of router-based internetworking, but
who may not be familiar with CiscoIOS software
• System administrators who are responsible for installing and configuring internetworking
equipment, and who are familiar with CiscoIOS software
Organization
The Cisco 6400 Software Setup Guide is organized into the following chapters and appendixes:
Chapter 1 Product Overview Describes the Cisco 6400 system and network
management options.
Chapter 2 Basic NSP Configuration Describes how to perform basic configuration
for the NSP.
Chapter 3 Basic NRP Configuration Describes how to perform basic configuration
for the NRP-1, NRP-2, and NRP-2SV.
Chapter 4 Node Line Card Interface
Configuration
Describes how to manually configure the
ATM interfaces for the NLCs.
Chapter 5 Redundancy and SONET APS
Configuration
Describes how to configure redundancy
among the NSP, NRP, and NLC components.
Chapter 6 SNMP, RMON, and Alarm
Configuration
Describes how to use SNMP, RMON, and
alarms on the Cisco 6400.
Appendix A Web Console Describes how to install and use the Web
Console application.
Appendix B Upgrading Software on the Cisco
6400
Describes how to upgrade software images on
the Cisco 6400.
Appendix C Optimizing the Number of Virtual
Connections on the Cisco 6400
Describes how to optimize the number of
virtual connections on the Cisco 6400.
Glossary — Defines the acronyms and terms used in this
guide.
- Text Part Number: OL-1183-04 1
- Contents 10
- OL-1183-04 10
- Document Objectives 11
- Related Documentation 11
- Audience 12
- Organization 12
- Conventions 13
- Obtaining Documentation 14
- Documentation CD-ROM 15
- Ordering Documentation 15
- Documentation Feedback 15
- Cisco.com 16
- Technical Assistance Center 16
- Product Overview 19
- Cisco 6400 System 20
- Node Switch Processor 21
- Node Route Processor 21
- Node Line Card 23
- Basic NSP Configuration 25
- Verifying DHCP 27
- ATM Address 28
- Verifying the ATM Address 30
- Internal Cross-Connections 34
- Example—Internal PVC 35
- Example—Internal PVP 36
- Network Clocking 38
- Network Routing 42
- NRP-2 and NRP-2SV Support 43
- System Logging 45
- Console and Telnet Access 45
- SNMPv3 Proxy Forwarder 46
- Storing the NSP Configuration 47
- Example—Disk0: versus Slot0: 49
- Basic NRP Configuration 51
- Initial NRP-1 Configuration 52
- Configuring the NRP-1 53
- Setting the I/O Memory Size 56
- Restrictions 58
- Example—Main ATM Interface 61
- Example—ATM Subinterface 61
- Changing the MTU on the NRP-2 62
- PAM mailbox serial interface: 68
- Permanent Virtual Circuits 70
- Configuring VC Classes 74
- Configuring PVC Discovery 76
- Verifying PVC Discovery 78
- Verifying PVC Traffic Shaping 79
- NLC Interface Identification 81
- Autoconfiguration 82
- ATM Interface Types 83
- Configuring UNIs 84
- Network-to-Network Interfaces 85
- Verifying NNI Configuration 86
- Configuring IISP Interfaces 87
- NLC Interface Clocking 88
- DS3 NLC Interface Options 90
- Memory Requirements 94
- NSP Redundancy 95
- Synchronizing Redundant NSPs 96
- PCMCIA Disk Mirroring 97
- Verifying Blind Copying 101
- Example—Disk Synchronization 102
- Examples 103
- NRP Redundancy 107
- Verifying NRP Redundancy 108
- NLC Redundancy 109
- Verifying NLC Redundancy 110
- Verifying SONET APS 112
- • Remote Monitoring, page 6-4 117
- • Alarms, page 6-4 117
- Remote Monitoring 120
- Verifying Temperature Alarms 121
- Clearing Alarms 122
- Web Console 123
- Web Console Installation 124
- Using the Web Console 126
- AppendixA Web Console 127
- FigureA-1 Update Page 128
- Accessing the Web Console 129
- Navigating in Web Console 131
- System Reload Options 134
- Configuring Redundancy 135
- IP Address Management 136
- Setting Static Routes 137
- SNMP Management 138
- Entering System Options 139
- Entering Community Strings 140
- Adding Trap Managers 140
- NRP Status 141
- Subscriber Management 141
- Step 2 Click Remove 143
- System Status 144
- FigureA-13 System Status 145
- Loading New Web Console Pages 146
- Recommendations 147
- Reload the Secondary NRP-1 156
- Reloading the Secondary NRP-1 159
- 2. Reload the Secondary NSP 160
- Prerequisites 161
- Reload the Secondary NSP 161
- Reloading the Secondary NSP 164
- Verifying VCI Values 169
- Shrinking ITT Blocks 172
- Displaying ITT Allocation 172
- GLOSSARY 175
- Glossary 176
Relacionado con productos y manuales para Cámaras De Seguridad Cisco 6400
Cámaras De Seguridad Cisco WVC54GCA Guía de usuario
(55 paginas)
(55 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.158 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales