Cisco 6400 Guia de preparacion Pagina 34
- Pagina / 198
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2-10
Cisco 6400 Software Setup Guide
OL-1183-04
Chapter2 Basic NSP Configuration
Internal Cross-Connections
!
Verifying the NME Interface Configuration
Use the show interface EXEC command to verify successful configuration of the NME interface on the
NSP. If the NSP is configured for NME consolidation, use show interface BVI 1. On an NSP configured
to use a separate NME interface, use show interface ethernet 0/0/0. Check that the output shows:
• That the NME interface and line protocol is “up”
• A valid IP address
• That packets are input and output
Switch# show interface BVI 1
BVI1 is up, line protocol is up
Hardware is BVI, address is 0050.736f.5756 (bia 0000.0000.0000)
Internet address is 172.194.71.11/24
MTU 4470 bytes, BW 10000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/0, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
53 packets input, 3180 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
57 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
Switch#
Internal Cross-Connections
The following sections describe minimal procedures for creating virtual circuits (VCs) and virtual paths
(VPs).
Note Soft VCs between the NRP and NSP are not supported.
For more information, see the following chapters of the ATM Switch Router Software Configuration
Guide:
• “Configuring Virtual Connections” (VCs)
• “Configuring ATM Network Interfaces” (VPs, including shared and hierarchical VP tunnels)
- Text Part Number: OL-1183-04 1
- Contents 10
- OL-1183-04 10
- Document Objectives 11
- Related Documentation 11
- Audience 12
- Organization 12
- Conventions 13
- Obtaining Documentation 14
- Documentation CD-ROM 15
- Ordering Documentation 15
- Documentation Feedback 15
- Cisco.com 16
- Technical Assistance Center 16
- Product Overview 19
- Cisco 6400 System 20
- Node Switch Processor 21
- Node Route Processor 21
- Node Line Card 23
- Basic NSP Configuration 25
- Verifying DHCP 27
- ATM Address 28
- Verifying the ATM Address 30
- Internal Cross-Connections 34
- Example—Internal PVC 35
- Example—Internal PVP 36
- Network Clocking 38
- Network Routing 42
- NRP-2 and NRP-2SV Support 43
- System Logging 45
- Console and Telnet Access 45
- SNMPv3 Proxy Forwarder 46
- Storing the NSP Configuration 47
- Example—Disk0: versus Slot0: 49
- Basic NRP Configuration 51
- Initial NRP-1 Configuration 52
- Configuring the NRP-1 53
- Setting the I/O Memory Size 56
- Restrictions 58
- Example—Main ATM Interface 61
- Example—ATM Subinterface 61
- Changing the MTU on the NRP-2 62
- PAM mailbox serial interface: 68
- Permanent Virtual Circuits 70
- Configuring VC Classes 74
- Configuring PVC Discovery 76
- Verifying PVC Discovery 78
- Verifying PVC Traffic Shaping 79
- NLC Interface Identification 81
- Autoconfiguration 82
- ATM Interface Types 83
- Configuring UNIs 84
- Network-to-Network Interfaces 85
- Verifying NNI Configuration 86
- Configuring IISP Interfaces 87
- NLC Interface Clocking 88
- DS3 NLC Interface Options 90
- Memory Requirements 94
- NSP Redundancy 95
- Synchronizing Redundant NSPs 96
- PCMCIA Disk Mirroring 97
- Verifying Blind Copying 101
- Example—Disk Synchronization 102
- Examples 103
- NRP Redundancy 107
- Verifying NRP Redundancy 108
- NLC Redundancy 109
- Verifying NLC Redundancy 110
- Verifying SONET APS 112
- • Remote Monitoring, page 6-4 117
- • Alarms, page 6-4 117
- Remote Monitoring 120
- Verifying Temperature Alarms 121
- Clearing Alarms 122
- Web Console 123
- Web Console Installation 124
- Using the Web Console 126
- AppendixA Web Console 127
- FigureA-1 Update Page 128
- Accessing the Web Console 129
- Navigating in Web Console 131
- System Reload Options 134
- Configuring Redundancy 135
- IP Address Management 136
- Setting Static Routes 137
- SNMP Management 138
- Entering System Options 139
- Entering Community Strings 140
- Adding Trap Managers 140
- NRP Status 141
- Subscriber Management 141
- Step 2 Click Remove 143
- System Status 144
- FigureA-13 System Status 145
- Loading New Web Console Pages 146
- Recommendations 147
- Reload the Secondary NRP-1 156
- Reloading the Secondary NRP-1 159
- 2. Reload the Secondary NSP 160
- Prerequisites 161
- Reload the Secondary NSP 161
- Reloading the Secondary NSP 164
- Verifying VCI Values 169
- Shrinking ITT Blocks 172
- Displaying ITT Allocation 172
- GLOSSARY 175
- Glossary 176
Relacionado con productos y manuales para Cámaras De Seguridad Cisco 6400
Cámaras De Seguridad Cisco WVC54GCA Guía de usuario
(55 paginas)
(55 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.123 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales