Cisco 6400 Guia de preparacion Pagina 14
- Pagina / 198
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
xiv
Cisco 6400 Software Setup Guide
OL-1183-04
Preface
Obtaining Documentation
Keyboard
This guide uses the following conventions for typing keys:
Notes, Timesavers, Tips, Cautions, and Warnings
The following conventions are used to attract the reader's attention:
Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in
this manual.
Timesaver Means the described action saves time. You can save time by performing the action described in the
paragraph.
Tip Means the following information might help you solve a problem.
Caution Means reader be careful. You are capable of doing something that might result in equipment damage or
loss of data.
Warning
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. To see translations of the warnings that appear in
this publication, refer to the Regulatory Compliance and Safety Information document that
accompanied this device.
Obtaining Documentation
The following sections provide sources for obtaining documentation from Cisco Systems.
World Wide Web
You can access the most current Cisco documentation on the World Wide Web at the following sites:
• http://www.cisco.com
Convention Description
Z Keys are indicated in capital letters but are not case sensitive.
^ orCtrl Represents the Control key. For example, when you read ^D or Ctrl-D, you
should hold down the Control key while you press the D key.
- Text Part Number: OL-1183-04 1
- Contents 10
- OL-1183-04 10
- Document Objectives 11
- Related Documentation 11
- Audience 12
- Organization 12
- Conventions 13
- Obtaining Documentation 14
- Documentation CD-ROM 15
- Ordering Documentation 15
- Documentation Feedback 15
- Cisco.com 16
- Technical Assistance Center 16
- Product Overview 19
- Cisco 6400 System 20
- Node Switch Processor 21
- Node Route Processor 21
- Node Line Card 23
- Basic NSP Configuration 25
- Verifying DHCP 27
- ATM Address 28
- Verifying the ATM Address 30
- Internal Cross-Connections 34
- Example—Internal PVC 35
- Example—Internal PVP 36
- Network Clocking 38
- Network Routing 42
- NRP-2 and NRP-2SV Support 43
- System Logging 45
- Console and Telnet Access 45
- SNMPv3 Proxy Forwarder 46
- Storing the NSP Configuration 47
- Example—Disk0: versus Slot0: 49
- Basic NRP Configuration 51
- Initial NRP-1 Configuration 52
- Configuring the NRP-1 53
- Setting the I/O Memory Size 56
- Restrictions 58
- Example—Main ATM Interface 61
- Example—ATM Subinterface 61
- Changing the MTU on the NRP-2 62
- PAM mailbox serial interface: 68
- Permanent Virtual Circuits 70
- Configuring VC Classes 74
- Configuring PVC Discovery 76
- Verifying PVC Discovery 78
- Verifying PVC Traffic Shaping 79
- NLC Interface Identification 81
- Autoconfiguration 82
- ATM Interface Types 83
- Configuring UNIs 84
- Network-to-Network Interfaces 85
- Verifying NNI Configuration 86
- Configuring IISP Interfaces 87
- NLC Interface Clocking 88
- DS3 NLC Interface Options 90
- Memory Requirements 94
- NSP Redundancy 95
- Synchronizing Redundant NSPs 96
- PCMCIA Disk Mirroring 97
- Verifying Blind Copying 101
- Example—Disk Synchronization 102
- Examples 103
- NRP Redundancy 107
- Verifying NRP Redundancy 108
- NLC Redundancy 109
- Verifying NLC Redundancy 110
- Verifying SONET APS 112
- • Remote Monitoring, page 6-4 117
- • Alarms, page 6-4 117
- Remote Monitoring 120
- Verifying Temperature Alarms 121
- Clearing Alarms 122
- Web Console 123
- Web Console Installation 124
- Using the Web Console 126
- AppendixA Web Console 127
- FigureA-1 Update Page 128
- Accessing the Web Console 129
- Navigating in Web Console 131
- System Reload Options 134
- Configuring Redundancy 135
- IP Address Management 136
- Setting Static Routes 137
- SNMP Management 138
- Entering System Options 139
- Entering Community Strings 140
- Adding Trap Managers 140
- NRP Status 141
- Subscriber Management 141
- Step 2 Click Remove 143
- System Status 144
- FigureA-13 System Status 145
- Loading New Web Console Pages 146
- Recommendations 147
- Reload the Secondary NRP-1 156
- Reloading the Secondary NRP-1 159
- 2. Reload the Secondary NSP 160
- Prerequisites 161
- Reload the Secondary NSP 161
- Reloading the Secondary NSP 164
- Verifying VCI Values 169
- Shrinking ITT Blocks 172
- Displaying ITT Allocation 172
- GLOSSARY 175
- Glossary 176
Relacionado con productos y manuales para Cámaras De Seguridad Cisco 6400
Cámaras De Seguridad Cisco WVC54GCA Guía de usuario
(55 paginas)
(55 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales