Cisco 6400 Guia de preparacion Pagina 29
- Pagina / 198
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2-5
Cisco 6400 Software Setup Guide
OL-1183-04
Chapter2 Basic NSP Configuration
ATM Address
Note The first 13 bytes of the address make up a switch prefix used by ILMI in assigning addresses to end
stations connected to User-Network Interface (UNI) ports.
• MAC address of the NSP—6 bytes (used to distinguish multiple end system identifier [ESI]
addresses)
Note Both MAC address fields in the ATM address are the same, but they will not be the same as the address
printed on the chassis label.
• Selector equals 0—1 byte
Configuring the ATM Address Manually
Manually configuring the ATM address is required:
• To connect to another system using Interim Interswitch Signaling Protocol (IISP). Using IISP
requires disabling PNNI, which results in no ILMI support.
• To configure a new ATM address that replaces the previous ATM address and generates a new PNNI
node ID and peer group ID for migrating from flat to hierarchical PNNI.
• To connect to multiple levels of a PNNI hierarchy.
• To connect to a service provider network that requires you to use the addressing scheme for that
network.
• To use a particular style of addressing. For instance, in some circumstances a mnemonic scheme
might be useful for identifying nodes in an ATM network.
To configure a new ATM address, refer to the chapter “Configuring ATM and PNNI” in the ATM Switch
Router Software Configuration Guide.
Caution ATM addressing can lead to conflicts if not configured correctly. If you are configuring a new ATM
address, the old one must be completely removed from the configuration.
Example
The following example shows how to change the active ATM address, create a new address, verify that
it exists, and then delete the current active address. Using the ellipses (...) adds the default Media Access
Control (MAC) address as the last six bytes.
Switch(config)# atm address 47.0091.8100.5670.0000.0ca7.ce01...
Switch(config)# end
Switch# show atm addresses
Switch Address(es):
47.00918100000000410B0A1081.00410B0A1081.00 active
47.00918100567000000CA7CE01.00410B0A1081.00
Soft VC Address(es):
47.0091.8100.0000.0041.0b0a.1081.4000.0c80.0000.00 ATM0/0/0
47.0091.8100.0000.0041.0b0a.1081.4000.0c80.0000.63 ATM0/0/0.99
47.0091.8100.0000.0041.0b0a.1081.4000.0c80.0010.00 ATM0/0/1
47.0091.8100.0000.0041.0b0a.1081.4000.0c80.0020.00 ATM0/0/2
- Text Part Number: OL-1183-04 1
- Contents 10
- OL-1183-04 10
- Document Objectives 11
- Related Documentation 11
- Audience 12
- Organization 12
- Conventions 13
- Obtaining Documentation 14
- Documentation CD-ROM 15
- Ordering Documentation 15
- Documentation Feedback 15
- Cisco.com 16
- Technical Assistance Center 16
- Product Overview 19
- Cisco 6400 System 20
- Node Switch Processor 21
- Node Route Processor 21
- Node Line Card 23
- Basic NSP Configuration 25
- Verifying DHCP 27
- ATM Address 28
- Verifying the ATM Address 30
- Internal Cross-Connections 34
- Example—Internal PVC 35
- Example—Internal PVP 36
- Network Clocking 38
- Network Routing 42
- NRP-2 and NRP-2SV Support 43
- System Logging 45
- Console and Telnet Access 45
- SNMPv3 Proxy Forwarder 46
- Storing the NSP Configuration 47
- Example—Disk0: versus Slot0: 49
- Basic NRP Configuration 51
- Initial NRP-1 Configuration 52
- Configuring the NRP-1 53
- Setting the I/O Memory Size 56
- Restrictions 58
- Example—Main ATM Interface 61
- Example—ATM Subinterface 61
- Changing the MTU on the NRP-2 62
- PAM mailbox serial interface: 68
- Permanent Virtual Circuits 70
- Configuring VC Classes 74
- Configuring PVC Discovery 76
- Verifying PVC Discovery 78
- Verifying PVC Traffic Shaping 79
- NLC Interface Identification 81
- Autoconfiguration 82
- ATM Interface Types 83
- Configuring UNIs 84
- Network-to-Network Interfaces 85
- Verifying NNI Configuration 86
- Configuring IISP Interfaces 87
- NLC Interface Clocking 88
- DS3 NLC Interface Options 90
- Memory Requirements 94
- NSP Redundancy 95
- Synchronizing Redundant NSPs 96
- PCMCIA Disk Mirroring 97
- Verifying Blind Copying 101
- Example—Disk Synchronization 102
- Examples 103
- NRP Redundancy 107
- Verifying NRP Redundancy 108
- NLC Redundancy 109
- Verifying NLC Redundancy 110
- Verifying SONET APS 112
- • Remote Monitoring, page 6-4 117
- • Alarms, page 6-4 117
- Remote Monitoring 120
- Verifying Temperature Alarms 121
- Clearing Alarms 122
- Web Console 123
- Web Console Installation 124
- Using the Web Console 126
- AppendixA Web Console 127
- FigureA-1 Update Page 128
- Accessing the Web Console 129
- Navigating in Web Console 131
- System Reload Options 134
- Configuring Redundancy 135
- IP Address Management 136
- Setting Static Routes 137
- SNMP Management 138
- Entering System Options 139
- Entering Community Strings 140
- Adding Trap Managers 140
- NRP Status 141
- Subscriber Management 141
- Step 2 Click Remove 143
- System Status 144
- FigureA-13 System Status 145
- Loading New Web Console Pages 146
- Recommendations 147
- Reload the Secondary NRP-1 156
- Reloading the Secondary NRP-1 159
- 2. Reload the Secondary NSP 160
- Prerequisites 161
- Reload the Secondary NSP 161
- Reloading the Secondary NSP 164
- Verifying VCI Values 169
- Shrinking ITT Blocks 172
- Displaying ITT Allocation 172
- GLOSSARY 175
- Glossary 176
Relacionado con productos y manuales para Cámaras De Seguridad Cisco 6400
Cámaras De Seguridad Cisco WVC54GCA Guía de usuario
(55 paginas)
(55 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales