Cisco Catalyst 7500 Series Especificaciones Pagina 79
- Pagina / 303
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CHAPTER
2-1
Cisco 7500 Series Installation and Configuration Guide
OL-5008-03 B0
2
Preparing for Installation
This chapter includes specific information about required tools and parts, safety guidelines, and
preparatory information required to ensure a successful installation of your Cisco 7500 series router.
Do not unpack the Cisco 7500 series router until you are ready to install it. Keep the chassis in the
shipping container to prevent accidental damage until you have determined where you want it installed.
Use the appropriate unpacking documentation included with your Cisco 7500 series router.
The Cisco Information Packet provides safety, and service, and support information, and is included in
the shipping container, together with any companion publications you specified on your order. Inspect
all items for shipping damage. If anything is damaged, immediately contact a customer service
representative.
Sections in this chapter include the following:
• Tools and Parts You Need, page 2-1
• Safety Recommendations, page 2-2
• AC-Input and DC-Input Power Guidelines, page 2-7
• Plant Wiring Guidelines, page 2-10
• Site Environment, Chassis Temperature, and Airflow Guidelines, page 2-12
• Equipment Rack-Mounting Guidelines, page 2-15
• Environmental Monitoring and Reporting Overview for the Cisco 7500 Series, page 2-22
Tools and Parts You Need
Following are the tools and parts generally required to install your Cisco 7500 series router:
• Number 1 Phillips and 3/16-inch (0.476 cm) flat-blade screwdrivers; additional tools, parts, and
procedures listed and discussed in companion documentation
• Rack-mount kit (hardware and accompanying documentation)
If you are installing the Cisco 7500 series router in a rack, you might also need the following tools:
–
Number 2 Phillips screwdriver
–
1/4-inch flat-blade screwdriver
–
Tape measure
–
Level
- Configuration Guide 1
- CONTENTS 3
- Contents 10
- OL-5008-03 B0 10
- Audience 11
- Organization 11
- Related Documentation 12
- Conventions 13
- Safety Warnings 15
- Attention 16
- Figyelem! 16
- Avvertenza 16
- Advarsel 17
- ¡Advertencia! 17
- Varning! 17
- Restricted Area Warning 18
- Obtaining Documentation 19
- Documentation Feedback 20
- Submitting a Service Request 21
- Terms and Acronyms 24
- Cisco 7505 Overview 25
- Cisco 7505 CyBus Backplane 26
- Cisco 7505 Overview 27
- Cisco 7507 Overview 28
- Cisco 7507 Overview 29
- Cisco 7507-MX Overview 33
- Cisco 7507-MX Overview 34
- Cisco 7513 Overview 37
- Front-panel 38
- Cisco 7513 Overview 39
- 012345RSPRSP89101112 40
- Cisco 7513-MX Overview 42
- Cisco 7513-MX Overview 44
- Cisco 7576 Overview 47
- Cisco 7576 Overview 49
- Router A 50
- Router B 50
- CyBus Slot Number Assignments 51
- RSP2—Cisco 7505 53
- Common RSP Hardware Features 64
- RSP NVRAM 65
- RSP Flash Memory 65
- RSP SRAM 65
- RSP EEPROM 66
- RSP Auxiliary Port Pinout 67
- Arbiter Overview 72
- Chassis Interface Overview 72
- Cisco 7505 Fan Tray Assembly 74
- Cisco 7576) 75
- Interface Processor Overview 76
- System Software Overview 78
- Preparing for Installation 79
- Safety Recommendations 80
- Chassis Lifting Guidelines 81
- Safety Recommendations 82
- Plant Wiring Guidelines 88
- Plant Wiring Guidelines 89
- Top view of router 91
- Front of 92
- Power supplies 93
- Card cage 93
- System blower 93
- Intake air Exhaust air 93
- Noninterface processor end 95
- Interface processor end 95
- Cisco 7500 Series 100
- 7507-MX) 103
- Installing the Cisco 7505 118
- Installing the Cisco 7505 119
- Remove a module as follows: 120
- Install a module as follows: 120
- Rack-Mounting the Cisco7505 121
- Install the cable management 123
- Captive installation screws 131
- Cisco 7513 and Cisco 7576 134
- Unpacking Instructions 134
- Captive screws 142
- Power Supplies 143
- What Do I Do Now? 147
- What Do I Do Now? 148
- Recovering a Lost Password 157
- Configuring Interfaces 163
- Checking the Settings 167
- Copying Files to Flash Memory 173
- Removing/replacing 187
- Chassis interface 193
- Standoff 193
- AC receptacle 195
- On/off switch 195
- Cable retention 195
- DC OK LED 195
- Cisco 7507-MX 201
- AC POWER 203
- Guide tab slides up 207
- • LED board (MAS-7KLED=) 209
- Black (ground) 215
- Purple (+24V) 215
- Blower power connection 215
- Backplane 215
- Cisco 7576 Router 219
- Cisco7576 220
- Cage Assembly 223
- Exchanging the EEPROM Devices 225
- Blower module 228
- Chassis Cover Panels 229
- Backplane Maintenance Cover 231
- 7513-MX, and Cisco7576 232
- Troubleshooting Overview 240
- Cisco 7513-MX, and Cisco7576 250
- Subsystem 253
- Troubleshooting the RSP 256
- Using the RSP LEDs 259
- Using the Power Supply LEDs 261
- For the DC-input 264
- Removing RSP2 SIMMs 267
- Installing New RSP2 SIMMs 268
- Removing RSP4 and RSP8 DIMMs 273
- Configuration Bit Meanings 277
- Bits 0–3 278
- Configuration Bit Meanings 279
- Bit 10 and Bit 14 280
- Bit 11 and Bit 12 280
- Numerics 285
© 2020, manymanuals.es. Todos los derechos reservados | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales