Cisco WS-X4604-GWY - VoIP Gateway Especificaciones descargar pdf (Pagina 142)

8-14

Cisco Catalyst 4000 Access Gateway Module Installation and Configuration Note

OL-3008-01

Chapter 8 Configuring the DSP Farm

Troubleshooting the AGM

Gateway show tdm map slot 1

Connection Memories for TDM in slot 1

=====================================

Local connection memory, Stream/Channel:

00/000: 5000 5001 5100 5101 4000 4000 4000 4000 4000 4000

00/010: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

00/020: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

00/030: 4000 4000

01/000: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

01/010: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

01/020: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

01/030: 4000 4000

02/000: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

02/010: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

02/020: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

02/030: 4000 4000

03/000: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

03/010: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

03/020: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

03/030: 4000 4000

04/000: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

04/010: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

04/020: 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

Troubleshooting DSP

Use the debug dsp command to debug DSP services. These commands enable logging of IOS code

execution on the console. The log can be directed to an IOS buffer instead of the console by using the

logging buffered command in configure mode at the IOS CLI.

The debug dsp command uses this syntax:

[no] debug dsp [dsp_no | all | dsp_no chan chan_no [voice]]

Disabling debugging on one channel or DSP does not affect debug enable on another DSP or channel.

For example, the no debug dsp dsp_no command disables debugging on a particular DSP, but the no

debug dsp all command disables all DSP debugging.

Table 8-1 shows which SIMM each DSP is on:

Command Purpose

Gateway(config)# debug dsp dsp_no

Enables debugging on a given DSP.

Gateway(config)# debug dsp dsp_no

chan chan_no

Enables debugging on a given DSP and a signalling channel.

Gateway(config)# debug dsp dsp_no

chan chan_no voice

Enables debugging on a given DSP and a voice channel.

Gateway(config)# debug dsp all

Enables all debugging on all DSPs and channels.

Ta b l e 8 - 1

SIMM DSP Number

SIMM 1 DSP 0–5

SIMM 2 DSP 6–11

1 2 ... 137 138 139 140 141 142 143 144 145 146 147 ... 165 166

Comentarios a estos manuales

Sin comentarios

Cisco WS-X4604-GWY - VoIP Gateway Especificaciones Pagina 142

Comentarios a estos manuales

Relacionado con productos y manuales para Gateways / Controladores Cisco WS-X4604-GWY - VoIP Gateway