Cisco WS-X4604-GWY - VoIP Gateway Especificaciones Pagina 84
- Pagina / 166
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5-10
Cisco Catalyst 4000 Access Gateway Module Installation and Configuration Note
OL-3008-01
Chapter 5 Configuring the Voice Interfaces
MGCP Configuration
The following example shows the overall configuration required to enable MGCP on a T1/PRI line:
isdn switch-type primary-5ess
controller T1 1/0
framing crc4
linecode hdb3
pri-group timeslots 1-24 service mgcp
interface Serial1/0:23
no ip address
no logging event link-status
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
isdn bind-l3 ccm-manager
dial-peer voice 1 pots
application mgcpapp
port 1/0:0
Configuring E1 Interfaces
To configure a new E1 interface (balanced or unbalanced) or to change the configuration of an existing
interface, use the following procedure:
Step 1 Identify the port number and enter line-specific information provided by your local carrier.
a. Choose the E1/PRI interface to configure by entering the following command from Global
configuration mode:
Gateway(config)# controller e1 1/0
This example configures an E1 interface in slot 1 and unit 0.
b. Specify the framing type:
Gateway(config-controller)# framing crc4
c. Specify the line code format:
Gateway(config-controller)# linecode hdb3
Step 2 Configure parameters for the voice interface.
a. Specify the PRI group and time slots to be mapped:
Gateway(config-controller)# pri-group timeslots 1-31 service mgcp
b. Configure each PRI group as a virtual serial interface:
Gateway(config-controller)# interface serial 1/0:15
c. Specify the E1 interface and unit number to modify:
interface Serial1/0:15
no ip address
no logging event link-status
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
Step 3 Configure the PRI port by entering the following command:
Gateway(controller-e1)# pri-group timeslots 1-31 service mgcp
- Cisco Catalyst 4000 1
- Access Gateway Module 1
- CONTENTS 3
- Contents 4
- Audience 9
- Organization 9
- Conventions 10
- Safety Overview 11
- Related Documentation 12
- Obtaining Documentation 13
- Documentation Feedback 14
- Cisco.com 14
- Technical Assistance Center 15
- Overview 17
- IP Telephony Campus 18
- Large Branch Office 18
- • the console port on the AGM 19
- Hardware Features 20
- Cisco Catalyst 4000 DSP Set 21
- Data Interface Modules 21
- Voice Interface Modules 22
- Signaling Support on AGM 23
- Switch-Type Support on AGM 23
- Software Features 24
- Security 25
- Resiliency 25
- Network Management Support 26
- Preparing to Install the AGM 27
- Installing the AGM 29
- Hot-Swapping Features 31
- Checking the AGM Operation 32
- Power Supply 1 34
- Power Supply 2 34
- WAN Interface Modules 35
- SEE MANUAL 36
- INSTALLATION 36
- Straight-through 41
- RJ-11-to-RJ-11 cable 41
- RJ-11 ports 41
- RJ-11 wall jack 41
- RJ-21 Connectors 42
- Velcro strap 43
- ConfigurableNot used 45
- RJ-48S ports 47
- RJ-48S wall jack 47
- RJ-48C ports 48
- NT1 device 48
- RJ-45-to-RJ-45 cable 48
- S/T port 48
- RJ-48C-to-RJ-48C cable 50
- RJ-48C wall jack 50
- Booting the AGM 53
- Accessing the AGM 54
- Configuring the Console Port 55
- Connecting a Terminal 56
- Connecting a Modem 56
- Using the Cisco IOS CLI 57
- Getting Help 58
- Command Modes 58
- Gateway(config-if)# 59
- (config 59
- Gateway(config-dial-peer)# 59
- Saving Configuration Changes 60
- Table 4-2 ISDN Switch Types 68
- Configuring T1 Interfaces 69
- Configuring E1 Interfaces 71
- Preparing to Configure VoIP 75
- Configuring Voice Interfaces 76
- MGCP Configuration 77
- Enabling MGCP 78
- • E&M Wink Start 81
- • E&M Delay Start 81
- H.323 Gateway Configuration 86
- FXS Emulation Example 90
- FXO Emulation Example 90
- E&M Emulation Example 91
- Configuring ISDN BRI Lines 92
- Gateway 1 Configuration 95
- T1/E1 Configuration (H.323) 96
- T1/PRI Configuration Example 97
- E1/PRI Configuration Example 98
- Configuration for AGM AGLB-1 99
- Configuration for AGM AGLB-2 100
- FXO Connection to PSTN 101
- San Jose Salt Lake City 102
- AGM SLC Configuration 103
- OL-3008-01 104
- Configuring FXS Voice Ports 106
- Validating the Configuration 107
- Fine-Tuning FXS Voice Ports 108
- Activating the Voice Port 110
- Sample Configuration 110
- Verifying the Configuration 120
- Sample Configurations 121
- Configuration File for Peer 1 124
- Configuration File for Peer 2 126
- Configuring the DSP Farm 129
- IP Telephony Gateway Mode 130
- Conferencing Service 131
- Transcoding Service 132
- Troubleshooting the AGM 137
- Troubleshooting Controller 138
- Troubleshooting Hardware 141
- Troubleshooting TDM 141
- Troubleshooting DSP 142
- SIMM 3 DSP 12–17 143
- SIMM 4 DSP 18–23 143
- Entering ROM Monitor Mode 145
- Configuring for Autoboot 146
- ROM Monitor Commands 147
- Debugging Commands 150
- Cookie Commands 151
- Upgrading the ROM Monitor 157
- Using Loss Plan Defaults 159
- Transmission Loss Plan 160
- Console Connector Pinouts 161
- Management Port Pinouts 161
- Identifying a Rollover Cable 163
- Connecting to a PC 164
- Connecting to a Terminal 164
Relacionado con productos y manuales para Gateways / Controladores Cisco WS-X4604-GWY - VoIP Gateway
(14 paginas)
(90 paginas)
(25 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales