Cisco WS-X4604-GWY - VoIP Gateway Especificaciones Pagina 8
- Pagina / 166
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
EFT DRAFT - CISCO CONFIDENTIAL
Contents
viii
Cisco Catalyst 4000 Access Gateway Module Installation and Configuration Note
OL-3008-01
APPENDIX
A Identifying Hardware Problems with the ROM Monitor A-1
Entering ROM Monitor Mode A-1
Configuring for Autoboot A-2
ROM Monitor Commands A-3
ROM Monitor Syntax Conventions A-3
Command Descriptions A-3
General Use Commands A-3
Debugging Commands A-6
Cookie Commands A-7
Configuration Register Command A-10
Modifying the Configuration Register from the Operating System Software A-11
Boot and System Image Recovery Commands A-11
Upgrading the ROM Monitor A-13
Upgrading the ROM Monitor from IOS CLI A-13
Upgrading the ROM Monitor from ROMMON A-13
APPENDIX
B Using Loss Plan Defaults B-1
Default Loss and Gain Values B-1
Transmission Loss Plan B-1
APPENDIX
C Connector and Cable Specifications C-1
Console Connector Pinouts C-1
Management Port Pinouts C-1
8-Port RJ21 FXS Module Connector Pinouts C-2
Cable and Adapter Specifications C-3
Crossover and Straight-Through Cable Pinouts C-3
Rollover Cable and Adapter Pinouts C-3
Identifying a Rollover Cable C-3
Connecting to a PC C-4
Connecting to a Terminal C-4
- Cisco Catalyst 4000 1
- Access Gateway Module 1
- CONTENTS 3
- Contents 4
- Audience 9
- Organization 9
- Conventions 10
- Safety Overview 11
- Related Documentation 12
- Obtaining Documentation 13
- Documentation Feedback 14
- Cisco.com 14
- Technical Assistance Center 15
- Overview 17
- IP Telephony Campus 18
- Large Branch Office 18
- • the console port on the AGM 19
- Hardware Features 20
- Cisco Catalyst 4000 DSP Set 21
- Data Interface Modules 21
- Voice Interface Modules 22
- Signaling Support on AGM 23
- Switch-Type Support on AGM 23
- Software Features 24
- Security 25
- Resiliency 25
- Network Management Support 26
- Preparing to Install the AGM 27
- Installing the AGM 29
- Hot-Swapping Features 31
- Checking the AGM Operation 32
- Power Supply 1 34
- Power Supply 2 34
- WAN Interface Modules 35
- SEE MANUAL 36
- INSTALLATION 36
- Straight-through 41
- RJ-11-to-RJ-11 cable 41
- RJ-11 ports 41
- RJ-11 wall jack 41
- RJ-21 Connectors 42
- Velcro strap 43
- ConfigurableNot used 45
- RJ-48S ports 47
- RJ-48S wall jack 47
- RJ-48C ports 48
- NT1 device 48
- RJ-45-to-RJ-45 cable 48
- S/T port 48
- RJ-48C-to-RJ-48C cable 50
- RJ-48C wall jack 50
- Booting the AGM 53
- Accessing the AGM 54
- Configuring the Console Port 55
- Connecting a Terminal 56
- Connecting a Modem 56
- Using the Cisco IOS CLI 57
- Getting Help 58
- Command Modes 58
- Gateway(config-if)# 59
- (config 59
- Gateway(config-dial-peer)# 59
- Saving Configuration Changes 60
- Table 4-2 ISDN Switch Types 68
- Configuring T1 Interfaces 69
- Configuring E1 Interfaces 71
- Preparing to Configure VoIP 75
- Configuring Voice Interfaces 76
- MGCP Configuration 77
- Enabling MGCP 78
- • E&M Wink Start 81
- • E&M Delay Start 81
- H.323 Gateway Configuration 86
- FXS Emulation Example 90
- FXO Emulation Example 90
- E&M Emulation Example 91
- Configuring ISDN BRI Lines 92
- Gateway 1 Configuration 95
- T1/E1 Configuration (H.323) 96
- T1/PRI Configuration Example 97
- E1/PRI Configuration Example 98
- Configuration for AGM AGLB-1 99
- Configuration for AGM AGLB-2 100
- FXO Connection to PSTN 101
- San Jose Salt Lake City 102
- AGM SLC Configuration 103
- OL-3008-01 104
- Configuring FXS Voice Ports 106
- Validating the Configuration 107
- Fine-Tuning FXS Voice Ports 108
- Activating the Voice Port 110
- Sample Configuration 110
- Verifying the Configuration 120
- Sample Configurations 121
- Configuration File for Peer 1 124
- Configuration File for Peer 2 126
- Configuring the DSP Farm 129
- IP Telephony Gateway Mode 130
- Conferencing Service 131
- Transcoding Service 132
- Troubleshooting the AGM 137
- Troubleshooting Controller 138
- Troubleshooting Hardware 141
- Troubleshooting TDM 141
- Troubleshooting DSP 142
- SIMM 3 DSP 12–17 143
- SIMM 4 DSP 18–23 143
- Entering ROM Monitor Mode 145
- Configuring for Autoboot 146
- ROM Monitor Commands 147
- Debugging Commands 150
- Cookie Commands 151
- Upgrading the ROM Monitor 157
- Using Loss Plan Defaults 159
- Transmission Loss Plan 160
- Console Connector Pinouts 161
- Management Port Pinouts 161
- Identifying a Rollover Cable 163
- Connecting to a PC 164
- Connecting to a Terminal 164
Relacionado con productos y manuales para Gateways / Controladores Cisco WS-X4604-GWY - VoIP Gateway
(14 paginas)
(90 paginas)
(25 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales