Cisco WS-X4604-GWY - VoIP Gateway Especificaciones Pagina 86
- Pagina / 166
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5-12
Cisco Catalyst 4000 Access Gateway Module Installation and Configuration Note
OL-3008-01
Chapter 5 Configuring the Voice Interfaces
H.323 Gateway Configuration
application mgcpapp
port 1/0:0
Where to Go Next
At this point, you should make sure that Cisco CallManager is properly configured to provision the voice
gateway and to configure MGCP endpoints or H.323 route patterns as required. Refer to the
documentation and online help provided with Cisco CallManager. Refer to the Cisco IOS software
configuration guide and command reference publications for more advanced configuration topics. For
troubleshooting information, refer to the system error messages and debug command reference
publications.
Access these publications on the Documentation CD-ROM that came with your gateway, or on the World
Wide Web from the Cisco home page.
H.323 Gateway Configuration
Compared to Media Gateway Control Protocol (MGCP), H.323 requires more configuration on a
gateway because the gateway must maintain the dial plan and route pattern. The gateway must have
enough information to direct calls to the correct end point, which must be an H.323-capable device.
When using H.323, ensure that you configure Cisco CallManager correctly to provision the AGM as an
H.323 gateway, with route patterns configured to route calls to a AGM.
To provision the gateway using Cisco CallManager Administration, select the Add a New Gateway
option from Device > Gateway. Assign the Gateway Type as H.323 Gateway, and the Device Protocol
as H.225.
To configure a route pattern using CCM Administrator, select Route Plan > Route Pattern and enter
the route pattern. Then select Cisco Catalyst 4000 AGM from a drop-down list, click the Route this
option button for the Route Option, and check the Provide Outside Dial Tone box for Offnet (the
default is OnNet).
To configure a specific interface or line signalling type, see the appropriate section provided later in this
chapter. In general, you need to perform the following steps to complete H.323 configuration.
Step 1 Identify the port number and enter line-specific information provided by your local carrier, as described
in the following sections:
• Configuring T1-CAS Analog Emulation (H.323), page 5-14
• ISDN BRI Configuration (H.323), page 5-17
• T1/E1 Configuration (H.323), page 5-22
Step 2 Configure parameters for the voice interface you are using, as described in the section referred to above.
Step 3 Configure H.323 endpoints connected to the AGM voice ports.
To configure plain old telephone service (POTS) dial peers, use the following command strings:
gateway(config)# dial-peer voice <number> pots
gateway(config-dial-peer)# destination-pattern <endpoint#>
gateway(config-dial-peer)# port 1/<portnumber>:<DS0groupnumber>
- Cisco Catalyst 4000 1
- Access Gateway Module 1
- CONTENTS 3
- Contents 4
- Audience 9
- Organization 9
- Conventions 10
- Safety Overview 11
- Related Documentation 12
- Obtaining Documentation 13
- Documentation Feedback 14
- Cisco.com 14
- Technical Assistance Center 15
- Overview 17
- IP Telephony Campus 18
- Large Branch Office 18
- • the console port on the AGM 19
- Hardware Features 20
- Cisco Catalyst 4000 DSP Set 21
- Data Interface Modules 21
- Voice Interface Modules 22
- Signaling Support on AGM 23
- Switch-Type Support on AGM 23
- Software Features 24
- Security 25
- Resiliency 25
- Network Management Support 26
- Preparing to Install the AGM 27
- Installing the AGM 29
- Hot-Swapping Features 31
- Checking the AGM Operation 32
- Power Supply 1 34
- Power Supply 2 34
- WAN Interface Modules 35
- SEE MANUAL 36
- INSTALLATION 36
- Straight-through 41
- RJ-11-to-RJ-11 cable 41
- RJ-11 ports 41
- RJ-11 wall jack 41
- RJ-21 Connectors 42
- Velcro strap 43
- ConfigurableNot used 45
- RJ-48S ports 47
- RJ-48S wall jack 47
- RJ-48C ports 48
- NT1 device 48
- RJ-45-to-RJ-45 cable 48
- S/T port 48
- RJ-48C-to-RJ-48C cable 50
- RJ-48C wall jack 50
- Booting the AGM 53
- Accessing the AGM 54
- Configuring the Console Port 55
- Connecting a Terminal 56
- Connecting a Modem 56
- Using the Cisco IOS CLI 57
- Getting Help 58
- Command Modes 58
- Gateway(config-if)# 59
- (config 59
- Gateway(config-dial-peer)# 59
- Saving Configuration Changes 60
- Table 4-2 ISDN Switch Types 68
- Configuring T1 Interfaces 69
- Configuring E1 Interfaces 71
- Preparing to Configure VoIP 75
- Configuring Voice Interfaces 76
- MGCP Configuration 77
- Enabling MGCP 78
- • E&M Wink Start 81
- • E&M Delay Start 81
- H.323 Gateway Configuration 86
- FXS Emulation Example 90
- FXO Emulation Example 90
- E&M Emulation Example 91
- Configuring ISDN BRI Lines 92
- Gateway 1 Configuration 95
- T1/E1 Configuration (H.323) 96
- T1/PRI Configuration Example 97
- E1/PRI Configuration Example 98
- Configuration for AGM AGLB-1 99
- Configuration for AGM AGLB-2 100
- FXO Connection to PSTN 101
- San Jose Salt Lake City 102
- AGM SLC Configuration 103
- OL-3008-01 104
- Configuring FXS Voice Ports 106
- Validating the Configuration 107
- Fine-Tuning FXS Voice Ports 108
- Activating the Voice Port 110
- Sample Configuration 110
- Verifying the Configuration 120
- Sample Configurations 121
- Configuration File for Peer 1 124
- Configuration File for Peer 2 126
- Configuring the DSP Farm 129
- IP Telephony Gateway Mode 130
- Conferencing Service 131
- Transcoding Service 132
- Troubleshooting the AGM 137
- Troubleshooting Controller 138
- Troubleshooting Hardware 141
- Troubleshooting TDM 141
- Troubleshooting DSP 142
- SIMM 3 DSP 12–17 143
- SIMM 4 DSP 18–23 143
- Entering ROM Monitor Mode 145
- Configuring for Autoboot 146
- ROM Monitor Commands 147
- Debugging Commands 150
- Cookie Commands 151
- Upgrading the ROM Monitor 157
- Using Loss Plan Defaults 159
- Transmission Loss Plan 160
- Console Connector Pinouts 161
- Management Port Pinouts 161
- Identifying a Rollover Cable 163
- Connecting to a PC 164
- Connecting to a Terminal 164
Relacionado con productos y manuales para Gateways / Controladores Cisco WS-X4604-GWY - VoIP Gateway
(14 paginas)
(90 paginas)
(25 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales