Cisco WS-X4604-GWY - VoIP Gateway Especificaciones Pagina 90
- Pagina / 166
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5-16
Cisco Catalyst 4000 Access Gateway Module Installation and Configuration Note
OL-3008-01
Chapter 5 Configuring the Voice Interfaces
Configuring T1-CAS Analog Emulation (H.323)
FXS Emulation Example
By connecting the T1-CAS port on a AGM to a T1 channel bank using FXS emulation, you can achieve
high port density when interconnecting POTS and VoIP endpoints. You can configure the dial plan for
this configuration by treating Cisco CallManager as the only H.323 endpoint, or by configuring H.323
endpoints on a AGM. If you configure Cisco CallManager as an H.323 endpoint, you must use
Cisco CallManager Administration to define the route patterns required to route calls to the AGM.
The following example illustrates how to configure a single DS-0 group. Repeat the relevant commands
to configure additional groups. This example is for a scenario in which all of the POTS devices
connected to a T1 channel bank are configured with a destination number beginning with 526. In this
example, Cisco CallManager has the host name CCM30 and is configured as an H.323 endpoint that
manages all the telephones and other devices on the IP network, which have numbers beginning with
525.
gateway(config)# interface FastEthernet5/0
gateway(config)# ipaddress 172.20.71.48 255.255.255.0
gateway(config)# no ip directed-broadcast
gateway(config)# no keepalive
gateway(config)# duplex auto
gateway(config)# speed 10
gateway(config)# controller T1 1/0
gateway(config-controller)# framing esf
gateway(config-controller)# clock source internal
gateway(config-controller)# linecode b8zs
gateway(config-controller)# dso-group 0 timeslots 1 type fxo-loop-start
gateway(config)# dial-peer voice 1 pots
gateway(config-dial-peer)# destination-pattern 526....
gateway(config-dial-peer)# port 1/0:0
gateway(config-dial-peer)# destination-pattern 525....
gateway(config-dial-peer)# session target dns:CCM30
gateway(config-dial-peer)# codec g711u1aw
gateway# line con 0
gateway# transport input none
gateway# line aux 0
gateway# line vty 0 4
gateway# login
gateway# no scheduler allocate
gateway# end
gateway# copy running-config startup-config
Building configuration. . .
[OK]
gateway#
FXO Emulation Example
To use FXO emulation to connect the T1-CAS port to the PSTN, you must have Direct Inward Dialing
(DID) enabled on incoming DS-0 groups. DID allows the gateway or Cisco CallManager to identify the
extension to which each call on an incoming DS-0 group is directed. Because DID only works on
incoming connections, you must have separate DS-0 groups allocated for incoming and outgoing calls.
To configure the gateway to accept DID information, enter the following command:
gateway(config-dial-peer)# direct-inward-dial
- Cisco Catalyst 4000 1
- Access Gateway Module 1
- CONTENTS 3
- Contents 4
- Audience 9
- Organization 9
- Conventions 10
- Safety Overview 11
- Related Documentation 12
- Obtaining Documentation 13
- Documentation Feedback 14
- Cisco.com 14
- Technical Assistance Center 15
- Overview 17
- IP Telephony Campus 18
- Large Branch Office 18
- • the console port on the AGM 19
- Hardware Features 20
- Cisco Catalyst 4000 DSP Set 21
- Data Interface Modules 21
- Voice Interface Modules 22
- Signaling Support on AGM 23
- Switch-Type Support on AGM 23
- Software Features 24
- Security 25
- Resiliency 25
- Network Management Support 26
- Preparing to Install the AGM 27
- Installing the AGM 29
- Hot-Swapping Features 31
- Checking the AGM Operation 32
- Power Supply 1 34
- Power Supply 2 34
- WAN Interface Modules 35
- SEE MANUAL 36
- INSTALLATION 36
- Straight-through 41
- RJ-11-to-RJ-11 cable 41
- RJ-11 ports 41
- RJ-11 wall jack 41
- RJ-21 Connectors 42
- Velcro strap 43
- ConfigurableNot used 45
- RJ-48S ports 47
- RJ-48S wall jack 47
- RJ-48C ports 48
- NT1 device 48
- RJ-45-to-RJ-45 cable 48
- S/T port 48
- RJ-48C-to-RJ-48C cable 50
- RJ-48C wall jack 50
- Booting the AGM 53
- Accessing the AGM 54
- Configuring the Console Port 55
- Connecting a Terminal 56
- Connecting a Modem 56
- Using the Cisco IOS CLI 57
- Getting Help 58
- Command Modes 58
- Gateway(config-if)# 59
- (config 59
- Gateway(config-dial-peer)# 59
- Saving Configuration Changes 60
- Table 4-2 ISDN Switch Types 68
- Configuring T1 Interfaces 69
- Configuring E1 Interfaces 71
- Preparing to Configure VoIP 75
- Configuring Voice Interfaces 76
- MGCP Configuration 77
- Enabling MGCP 78
- • E&M Wink Start 81
- • E&M Delay Start 81
- H.323 Gateway Configuration 86
- FXS Emulation Example 90
- FXO Emulation Example 90
- E&M Emulation Example 91
- Configuring ISDN BRI Lines 92
- Gateway 1 Configuration 95
- T1/E1 Configuration (H.323) 96
- T1/PRI Configuration Example 97
- E1/PRI Configuration Example 98
- Configuration for AGM AGLB-1 99
- Configuration for AGM AGLB-2 100
- FXO Connection to PSTN 101
- San Jose Salt Lake City 102
- AGM SLC Configuration 103
- OL-3008-01 104
- Configuring FXS Voice Ports 106
- Validating the Configuration 107
- Fine-Tuning FXS Voice Ports 108
- Activating the Voice Port 110
- Sample Configuration 110
- Verifying the Configuration 120
- Sample Configurations 121
- Configuration File for Peer 1 124
- Configuration File for Peer 2 126
- Configuring the DSP Farm 129
- IP Telephony Gateway Mode 130
- Conferencing Service 131
- Transcoding Service 132
- Troubleshooting the AGM 137
- Troubleshooting Controller 138
- Troubleshooting Hardware 141
- Troubleshooting TDM 141
- Troubleshooting DSP 142
- SIMM 3 DSP 12–17 143
- SIMM 4 DSP 18–23 143
- Entering ROM Monitor Mode 145
- Configuring for Autoboot 146
- ROM Monitor Commands 147
- Debugging Commands 150
- Cookie Commands 151
- Upgrading the ROM Monitor 157
- Using Loss Plan Defaults 159
- Transmission Loss Plan 160
- Console Connector Pinouts 161
- Management Port Pinouts 161
- Identifying a Rollover Cable 163
- Connecting to a PC 164
- Connecting to a Terminal 164
Relacionado con productos y manuales para Gateways / Controladores Cisco WS-X4604-GWY - VoIP Gateway
(14 paginas)
(90 paginas)
(25 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales