Cisco OL-4015-08 Manual de usuario Pagina 149

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 678
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 148
501
Cross-Platform Release Notes for Cisco IOS Release 12.0S
OL-1617-14 Rev. Q0
Caveats
Resolved Caveats—Cisco IOS Release 12.0(32)S12
SLOT 5:*May 9 21:43:48.547: %LC_SPA_DMLP-1-SPAHWBUNDLEERROR: Could not perform
required operation in SPA H/w for bundle Multilink2 in bflc_cx3_dmlp_frag_on_off SLOT
5:*May 9 21:44:10.727: %SPA_CHOC_DSX-3-ERROR: Multilink2 (cmd 203) Serial5/0/1/8:0:
response parsing failed. chnl 36, bid 1 -Traceback= 40031008 408924C0 4072B1BC
40899F64 4033DB90 4033E190 4033E5C0 4033E930 4033F448 4033F600 4015B53C 4015C020 SLOT
5:*May 9 21:44:10.735: %LC_SPA_DMLP-3-CFG_FAIL: bundle Multilink2 (id 1): bay 0 err
7 (del rx link)
Conditions: When we remove/add/remove all members from all the configured MLP bundles once
or several times, these tracebacks are seen.
Workaround: There is no workaround.
Further Problem Description: spabrg EFC mapping goes to a mismatch state, and the following is
seen:
SLOT 5:*May 9 21:59:26.771: %SPA_CHOC_DSX-3-HDLC_CTRL_ERR: SPA 5/0: 20 TX Chnl Queue
Overflow events on HDLC Controller were encountered.
CSCsq42803
Symptoms: The hw-module slot x qos account layer2 encapsulation command does not take effect
for an AToM connection.
Conditions: This symptom is observed when xconnect is configured under a VLAN.
Workaround: There is no workaround.
CSCsq55258
Symptoms: After a router reloads, sometimes the configuration for the gigE and POS OC12 SPA is
lost from the running configuration.
Conditions: This symptom is observed when the router is reloaded.
Workaround: There is no workaround.
CSCsq58341
Symptoms: If both L2 and L3 services co-exist on the same interface, you can no longer configure
urpf on the L3 subinterface after the fix for CSCsl09772. After the router reloads, the urpf command
will be erased from the L3 subinterface. You have to use the workaround to reapply the urpf
command.
Conditions: This symptom is observed when both L2 and L3 services are configured on the same
interface.
Workaround: Do the following:
1. Remove the L2 connection.
2. Add urpf on the L3 subinterface.
3. Re-add the L2 connection.
CSCsq67266
Symptoms: The pos delay triggers line command is configurable at the interface level of E3
channelized POS interfaces.
Conditions: This symptom is observed on a Cisco 12416 Internet series router that is booted with
the Cisco IOS Release 12.0(32)S nightly build of 05/19/08. The router contains an E3 CHOC48
linecard.
Workaround: There is no workaround.
CSCsq71212
Symptoms: EFC clock interrupts are causing a line card to crash.
Vista de pagina 148
1 2 ... 144 145 146 147 148 149 150 151 152 153 154 ... 677 678

Comentarios a estos manuales

Sin comentarios