Cisco 7600-ES20-GE3CXL-RF - Ethernet Services 20G Line Card Switch Manual de usuario Pagina 125

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 398
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 124
571
Caveats for Cisco IOS Release 12.2(33)SRD through 12.2(33)SRD8
OL-10394-05 Rev. R0
CSCsl32142
Symptoms: A router may reload after reporting SYS-3-OVERRUN or SYS-3-BADBLOCK error
messages. SYS-2-GETBUF with “Bad getbuffer” error may also be reported.
Condition: Occurs when PIM auto-RP is configured and IP multicast boundary is enabled with the
filter-autorp option.
Workaround: Configure IP multicast boundary without the filter-autorp option.
CSCsl68327
Symptoms: Packets may be lost during rekey.
Conditions: Occurs because IPSec transit packets may trigger invalid SPI.
Workaround: There is no workaround.
CSCsl71704
Symptoms: A receive access control list (rACL) with large ACL is not applied on interface if is QoS
configured.
Conditions: Occurs when rACL with large ACL is applied on an interface. It consumes over 60% of
ternary content addressable memory (TCAM) space. If the rACL is applied a second interface with
QoS, the configuration fails without displaying an error message.
Workaround: There is no workaround.
CSCsm28287
Symptoms: After shutting down a GRE tunnel interface, the active RP crashed and switchover took
place. The following error message was displayed:
%ALIGN-1-FATAL: Illegal access to a low address 13:02:45 UTC Fri Jan 18 2008 addr=0xD,
pc=0x7144A5A0, ra=0x7209FFF8, sp=0x5ABEE90 SLOT0:01:40:03: %DUMPER-3-PROCINFO: pid =
16409: (sbin/ios-base), terminated due to signal SIGBUS, Bus error (Invalid address
alignment) SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: zero at v0 v1
SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: R0 00000000 7A5FD854 EF4321F9
7A6452D0 SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: a0 a1 a2 a3 SLOT0:01:40:03:
%DUMPER-3-REGISTERS_INFO: 16409: R4 EF4321CD 0000000B 0000000B 00000000
SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: t0 t1 t2 t3 SLOT0:01:40:03:
%DUMPER-3-REGISTERS_INFO: 16409: R8 7CB96E10 00FDDBE0 00000000 EFFFFFFF
SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: t4 t5 t6 t7 SLOT0:01:40:03:
%DUMPER-3-REGISTERS_INFO: 16409: R12 00000000 F7E8E12F 00000000 00000000
SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: s0
Conditions: Occurred on a Cisco 7200 running an internal build of Cisco IOS Release 12.2SX.
Workaround: There is no workaround.
CSCsm47417
Symptoms: W2:setting ceExtSysBootImageList cause write memory to work incorrectly.
Conditions: Occurs after setting ceExtSysBootImageList to a new boot image from SNMP. The new
boot image in running-config is not copied to startup-config. Instead, a variable “d” will be copied
to startup-config after the write memory. The show bootvar command will show BOOT variable =
d.
Example: /jointfilesconvert/422273/bgl11-lab1-tftp1:/auto/sw/packages/snmpr/15.1.0.3/solaris2bin:3>
/jointfilesconvert/422273/bgl11-lab1-tftp1:/auto/sw/packages/snmpr/15.1.0.3/solaris2bin:3>getmany -v2c
10.64.68.138 public ceExtSysBootImageList ceExtSysBootImageList.2001 =
disk1:s72033-adventerprisek9_d/jointfilesconvert/422273/bg-vzsm47417test ceExtSysBootImageList.2017 =
disk1:s72033-adventerprisek9_d/jointfilesconvert/422273/bg-vzsm47417test
/jointfilesconvert/422273/bgl11-lab1-tftp1:/auto/sw/packages/snmpr/15.1.0.3/solaris2bin:4>setany -v2c
10.64.68.138 public ceExtSysBootImageList.2001 -o "disk1:" ceExtSysBootImageList.2001
= disk1: ------------------------------------------------ 7600-11-1# 00:02:56:
%SYS-5-CONFIG_I: Configured from 10.64.71.240 by snmp
Vista de pagina 124
1 2 ... 120 121 122 123 124 125 126 127 128 129 130 ... 397 398

Comentarios a estos manuales

Sin comentarios