Cisco 7600-ES20-GE3CXL-RF - Ethernet Services 20G Line Card Switch Manual de usuario descargar pdf (Pagina 251)

697

Caveats for Cisco IOS Release 12.2(33)SRD through 12.2(33)SRD8

OL-10394-05 Rev. R0

Aug 13 14:50:52.617 PDT: %RED-5-REDCHANGE: PRE B now Standby(0x1421 => 0x1411) Aug 13

14:50:54.113 PDT: %C10K_ALARM-6-INFO: CLEAR MAJOR RP A Secondary removed Aug 13

14:51:33.822 PDT: -Traceback= 415C75D8 4019FB1C 40694770 4069475C Aug 13 14:51:33.822

PDT: CONFIG SYNC: Images are same and incompatible

Aug 13 14:51:33.822 PDT: %ISSU-3-INCOMPATIBLE_PEER_UID: Image running on peer uid (2)

is the same -Traceback= 415CCC2C 415C75FC 4019FB1C 40694770 4069475C Aug 13

14:51:33.822 PDT: Config Sync: Bulk-sync failure due to Servicing Incompatibility.

Please check full list of mismatched commands via: show issu config-sync failures mcl

Aug 13 14:51:33.822 PDT: Config Sync: Starting lines from MCL file: aaa group server

radius RSIM ! <submode> "sg-radius" - ip radius source-interface GigabitEthernet6/0/0

Conditions: This symptom is observed if the aaa group server radius subcommand ip radius

source-interface CLI is configured on a box with dual PREs.

Workaround: If the customer does not use the aaa group server radius subcommand ip radius

source-interface interface, this will not be a problem.

If they use the aaa group server radius subcommand ip radius source-interface interface on a

Cisco 10000 router in simplex mode (a single PRE), this will not be a problem.

If they run with dual PREs, then they will need to remove the aaa group server radius subcommand

ip radius source- interface interface from the configuration as a workaround.

Removing the aaa group server radius subcommand ip radius source-interface interface from the

configuration could cause problems for the customer. The radius server may be expecting the request

to come from a specific source address. The router will now use the address of the interface the

packet egresses the router from, which may change over time as routes fluctuate.

• CSCsk07097

Symptoms: After clearing PPPoEoVLAN session, applying a HQoS policy on the VLAN fails.

Conditions: This issue occurs on a Cisco 10000 series router with PRE3 board. A session comes up

on a VLAN/QinQ, and HQoS is applied to that session. When the session is removed, applying a

HQoS policy on the VLAN/QinQ fails.

This only occurs if the session parent policy is configured with "bandwidth remaining ratio x".

Workaround: There is no workaround.

• CSCsk12238

Symptoms: Calls are torn down within a second after establishment.

Conditions: This symptom occurs when pinging from the client to the NAS gives "Request drop link

from bundle".

Workaround: Configure the dialer idle-timeout 0 command under the template. This will never

bring down the calls nor bring down the physical link.

template template1 dialer idle-timeout 0

• CSCsk19497

Symptoms: Service-policy is removed from Multilink Frame Relay (MFR) interface.

Conditions: Occurs during QoS stress testing while running the c10k3-p11-mz.122-32.8.86.SR

image. The issue is triggered by performing a shut/no shut on the interface.

Workaround: There is no workaround.

• CSCsk21328

Symptoms: Router crashes during shutdown or deletion of interface.

Conditions: Occurs on interfaces on which IPv6 is enabled.

Workaround: There is no workaround.

1 2 ... 246 247 248 249 250 251 252 253 254 255 256 ... 397 398

Comentarios a estos manuales

Sin comentarios

Cisco 7600-ES20-GE3CXL-RF - Ethernet Services 20G Line Card Switch Manual de usuario Pagina 251

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Cisco 7600-ES20-GE3CXL-RF - Ethernet Services 20G Line Card Switch