
696
Caveats for Cisco IOS Release 12.2(33)SRD through 12.2(33)SRD8
OL-10394-05 Rev. R0
Symptoms: Configuring a command with the string "do" inside a sub-mode may cause unexpected
behavior.
There is known issue that using the PVC names ending with "do" lead to refusing the command as
not valid. The error message "% Invalid input detected at ’^’ marker." will be displayed if the
command is executed in sub-mode. If it is executed in ATM mode, there will be no error reported,
but the pvc will be removed from configuration after reload.
Conditions: The symptom is observed when using "do" as shorthand for "domain," for example in
ipe domain CLI.
Workaround: Do not use "do" keyword as shorthand in commands inside a sub- mode.
Related to ATM PVC names: do not use PVC names ending with "do"
Further Problem Description: Commands starting with "do" will be interpreted as exec commands.
• CSCsj91123
Symptoms: Router reloads after authentication attempt fails on console.
Conditions: Occurs while performing AAA accounting. The accounting structure was freed twice,
which results in crash. Occurs when the aaa accounting send stop-record authentication failure
command is configured, which sends a stop record for authentication failure.
Workaround: Remove the aaa accounting send stop-record authentication failure command.
• CSCsj98198
Symptoms: The following error occurs:
%NETFLOW_AGGREGATION-4-OER_AGG_EXPORT_ERROR: OER Error receiving TT agg export packet
on RP
Conditions: Errors may be seen on Cisco 6500 running as Optimized Edge Routing (OER) border
router
Workaround: There is no workaround.
• CSCsk03336
Symptom: Interface counters on line cards may show incorrect packet input statistics in the output
of the show interface command.
Conditions: Occurs when the "CEF LC IPC Backg" process causes the line card CPU to exceed 90%.
This is seen when an unstable network causes excessive CEF updates.
Workaround: There is no workaround.
• CSCsk05653
Symptoms: The aaa group server radius subcommand ip radius source-interface will cause the
standby to fail to sync.
c10k-6(config)#aaa group server radius RSIM c10k-6(config-sg-radius)#ip radius
source-interface GigabitEthernet6/0/0
c10k-6#hw-module standby-cpu reset c10k-6# Aug 13 14:49:31.793 PDT:
%REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_NOT_PRESENT) Aug 13
14:49:31.793 PDT: %C10K_ALARM-6-INFO: ASSERT MAJOR RP A Secondary removed Aug 13
14:49:31.793 PDT: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) Aug
13 14:49:31.793 PDT: %REDUNDANCY-3-STANDBY_LOST: Standby processor fault
(PEER_REDUNDANCY_STATE_CHANGE) Aug 13 14:49:31.793 PDT: %REDUNDANCY-3-STANDBY_LOST:
Standby processor fault (PEER_NOT_PRESENT) Aug 13 14:49:31.793 PDT:
%REDUNDANCY-3-STANDBY_LOST: Standby processor fault (PEER_DOWN) Aug 13 14:49:31.813
PDT: %REDUNDANCY-3-IPC: cannot open standby port no such port Aug 13 14:49:32.117 PDT:
%RED-5-REDCHANGE: PRE B now Non-participant(0x1C11 => 0x1421) Aug 13 14:49:32.117 PDT:
%REDUNDANCY-5-PEER_MONITOR_EVENT: Active detected a standby insertion
(raw-event=PEER_REDUNDANCY_STATE_CHANGE(5))
Comentarios a estos manuales