Cisco 7600-ES20-GE3CXL-RF - Ethernet Services 20G Line Card Switch Manual de usuario Pagina 336

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 398
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 335
782
Caveats for Cisco IOS Release 12.2(33)SRD through 12.2(33)SRD8
OL-10394-05 Rev. R0
Conditions: The symptom will only happen in a mis-configuration where the TE tunnel interface
does not have an IP address configured.
Workaround: Tunnel using OSPF as IGP is required to configure tunnel IP address in order to
forward IP traffic. To fix this mis-configuration, use the loopback address for TE tunnel interface IP
address, such as ip unnumbered loopback 0 for tunnel address.
CSCso07811
Symptoms: Remote-id and circuit-id are no longer formatted as Type Length Value (TLV) in radius
packets.
CLI command to enable legacy behavior (formatting remote-id and circuit-id) 1. config t 2.
subscriber policy format_option82_for_cats
New behavior:
remote id 00046aacfc82 circuit id 00000009
Radius see it as:
*Apr 16 05:33:30.695: RADIUS: User-Name [1] 16 "aabb.cc00.6500" *Apr 16 05:33:30.695:
RADIUS: User-Password [2] 18 * *Apr 16 05:33:30.695: RADIUS: Calling-Station-Id [31]
14 "00046aacfc82" *Apr 16 05:33:30.695: RADIUS: NAS-Port-Type [61] 6 Virtual [5] *Apr
16 05:33:30.695: RADIUS: Vendor, Cisco [26] 31 *Apr 16 05:33:30.695: RADIUS: Cisco
AVpair [1] 25 "circuit-id- tag=00000009" *Apr 16 05:33:30.695: RADIUS: Vendor, Cisco
[26] 34 *Apr 16 05:33:30.695: RADIUS: Cisco AVpair [1] 28 "remote-id-
tag=00046aacfc82" *Apr 16 05:33:30.695: RADIUS: NAS-Port [5] 6 0
Legacy behavior:
remote id 00046aacfc82 circuit id 00000009
Radius see it as: (note the extra characters)
Mar 2 22:17:19.796: RADIUS: Calling-Station-Id [31] 15 "0|4|6aac.fc82" Mar 2
22:17:19.796: RADIUS: NAS-Port-Type [61] 6 Ethernet [15] Mar 2 22:17:19.796: RADIUS:
Vendor, Cisco [26] 32 Mar 2 22:17:19.796: RADIUS: Cisco AVpair [1] 26 "circuit-id-
tag=0|0|9|2|6" Mar 2 22:17:19.796: RADIUS: Vendor, Cisco [26] 35 Mar 2 22:17:19.796:
RADIUS: Cisco AVpair [1] 29 "remote-id- tag=0|4|6aac.fc82" Mar 2 22:17:19.796: RADIUS:
NAS-Port [5] 6 16777329 Mar 2 22:17:19.796: RADIUS: NAS-Port-Id [87] 25
"0|4|6aac.fc82:0|0|9|2|6"
Workaround: There is no workaround.
CSCso09237
Symptoms: A Cisco 7200 router crashes due to memory corruption.
Conditions: This symptom occurs when issuing "no ip routing" using a SSH session.
Workaround: There is no workaround.
CSCso09607
Symptoms: All or some of the following symptoms may be experienced: 1. Crash could occur during
GTPLB sticky timer expiration. 2. Crash could occur if show ip slb sticky gtp imsi command is
issued. 3. "%SLB-4-UNEXPECTED: Unexpected error: real num_clients counter already 0"
message might be displayed. 4. Unexpected timer expiration for the same sticky object could occur.
This could be realized only with debug ip slb sticky gtp imsi. The frequency of expiration might
increase periodically.
Conditions: The symptoms are observed under all of the following conditions: - GTPLB sticky and
non-zero sticky idle timer should be configured under vserver. - Query should be configured under
vserver. - At least one NSAPI’s pdp session context should have been deleted in GGSN which is not
known to GTPLB when GGSN receives the pdp status query for all NSAPIs from GTPLB. - On
sticky timer expiration, the response for GTPLB query should contain status for fewer number of
NSAPIs than GTPLB has. Sticky object with the NSAPI should have been deleted after n number
of retries and the deletion should have occurred at least twice.
Vista de pagina 335
1 2 ... 331 332 333 334 335 336 337 338 339 340 341 ... 397 398

Comentarios a estos manuales

Sin comentarios