Cisco 7600-ES20-GE3CXL-RF - Ethernet Services 20G Line Card Switch Manual de usuario descargar pdf (Pagina 244)

690

Caveats for Cisco IOS Release 12.2(33)SRD through 12.2(33)SRD8

OL-10394-05 Rev. R0

Conditions: This symptom has been observed when using a removable flash card, such as an ATA

flash car or CF card, that is formatted to use DOSFS. The removable flash card is removed from the

router and inserted into a laptop that is running a version of the Microsoft Windows operating

system. A "New Folder" directory is created on the flash card and the flash card is removed from

the laptop and re-inserted into the router. Entering the dir command on the router may fail to show

all of the stored files or may crash the router.

Workaround: Remove or rename all files and directories having names with embedded spaces so that

no file or directory names contains embedded spaces.

• CSCsh67875

Symptoms: CLI rejects the following configuration on GSR Eng 3 GigE subinterface:

policy-map CC_CE->PE_ETM_G=1M_M=200K

class multicast_limit

police cir 200000 bc 4470 be 4470 <<<<<<this is causing the error msg..

conform-action transmit

exceed-action drop

Following error message was displayed:

"Errormulti-action policy not supported on GigabitEthernet9/2.2" when trying to apply

ingress policy CC_CE->PE_ETM_G=1M_M=200K.

Conditions: Occurs when police command has multi-line command

Workaround: Put command on one line, such as:

policy-map CC_CE->PE_ETM_G=1M_M=200K

class multicast_limit

police cir 200000 bc 4470 be 4470 conform-action transmit exceed-action drop

• CSCsh88532

Symptoms: Unable to change QoS trust settings on WiSM interfaces from trust CoS.

Conditions: When certain networks need to trust DSCP or IP-precedence, WiSM could not set

qos-trust values.

Workaround: Use manual LAG configuration to set the individual gigabit interfaces and port

channels to set the QoS trust to DSCP or IP-precedence instead of WiSM default CoS.

• CSCsh91974

Symptoms: The Route Processor (RP) crashes.

Conditions: Some of the Protocol Independent Multicast (PIM) CLI commands are causing the

active RP to crash. The crash happens only when these commands are configured while in

control-plane policing subconfiguration mode. Normally, any global relevant configuration should

automatically exit the subconfiguration prompt and also accept the command. In this case, the PIM

command is rejected and the RP crashes. The same PIM commands work fine when entered under

global configuration mode (where they belong) or under other subconfiguration modes.

Workaround: Use the exit command to exit the main configuration prompt before configuring

PIM-related commands.

• CSCsi17158

Symptoms: Devices running Cisco IOS may reload with the error message "System returned to ROM

by abort at PC 0x0" when processing SSHv2 sessions. A switch crashes. We have a script running

that will continuously ssh-v2 into the 3560 then close the session normally. If the vty line that is

being used by SSHv2 sessions to the device is cleared while the SSH session is being processed, the

next time an ssh into the device is done, the device will crash.

1 2 ... 239 240 241 242 243 244 245 246 247 248 249 ... 397 398

Comentarios a estos manuales

Sin comentarios

Cisco 7600-ES20-GE3CXL-RF - Ethernet Services 20G Line Card Switch Manual de usuario Pagina 244

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Cisco 7600-ES20-GE3CXL-RF - Ethernet Services 20G Line Card Switch